ABB IRB 390 Product Manual Download Page 241

Page: 241 / 346

Note

Action

CAUTION

Whenever parting/mating motor and gearbox, the
gears may be damaged if excessive force is used.

xx1900001834

Remove the motor by sliding it out on the guide
pins and lift it off.

Refitting the motor

Use these procedures to refit the axis-1 motor.

Refitting the axis-1, axis-2 or axis-3 motor

Note

Action

O-ring: 3HAB3772-102

Lubricate the new o-ring with grease and fit it to
the motor flange.

Anti-seize paste: 3HAC070875-002
(Molykote P1900)

xx1900001962

Guide pin, M8x150: 3HAC15520-2

If not already fitted, fasten two guide pins to op-
posite screw holes.

Tip

Lubricate the guide pins with some grease to
make the motor slide better.

CAUTION

Whenever parting/mating motor and gearbox, the
gears may be damaged if excessive force is used.

Continues on next page

Product manual - IRB 390

241

3HAC066566-001 Revision: B

5 Repair

5.6.1 Replacing the axis-1, axis 2 and axis-3 motor

Continued

Summary of Contents for IRB 390


























































































































































































































































































































































Search results

Summary of Contents for IRB 390

Reviews:

Brands by name

Popular brands

ABB IRB 390, Product Manual

Search results

Summary of Contents for IRB 390

Reviews:

Brands by name

Popular brands