ABB IRB 390 Product Manual Download

Page: 183 / 346

Note

Action

M6x16 8.8-A2F (3 pcs)

xx1900000753

Secure the SMB bracket with the screws.

xx2000002210

Reconnect the connector to X1 on the SMB board.

Checking the layout

Note

Action

Compare the cable layout to the picture previously
taken and verify that everything is connected and
routed correctly.

Refitting the upper end of the telescopic shaft

Note

Action

Cleaning agent: Isopropanol.

Clean the friction shim, the sealing ring and the
contact surfaces with isopropanol. Inspect for
damage.

Friction shim: 3HAC060200-001.
Sealing ring: 3HAC060263-001

Replace if damaged.

Continues on next page

Product manual - IRB 390

183

3HAC066566-001 Revision: B

5 Repair

5.4.4 Replacing the cable harness

Continued

Summary of Contents for IRB 390


























































































































































































































































































































































Search results

Summary of Contents for IRB 390

Reviews:

Related manuals for IRB 390

Brands by name

Popular brands

ABB IRB 390, Product Manual

Search results

Summary of Contents for IRB 390

Reviews:

Related manuals for IRB 390

Brands by name

Popular brands