ABB IRB 390 Product Manual Download Page 20

Page: 20 / 346

Description

Symbol

See user documentation

xx0900000813

Read user documentation for details.
Which manual to read is defined by the symbol:

•

No text:

Product manual

•

EPS:

Application manual - Electronic Position Switches

Before disassembly, see product manual

xx0900000816

Do not disassemble

xx0900000815

Disassembling this part can cause injury.

Extended rotation

xx0900000814

This axis has extended rotation (working area) compared to
standard.

Brake release

xx0900000808

Pressing this button will release the brakes. This means that
the robot arm can fall down.

Continues on next page

Product manual - IRB 390

3HAC066566-001 Revision: B

1 Safety

1.2.2 Safety symbols on manipulator labels

Continued

Summary of Contents for IRB 390


























































































































































































































































































































































Search results

Summary of Contents for IRB 390

Reviews:

Brands by name

Popular brands

ABB IRB 390, Product Manual

Search results

Summary of Contents for IRB 390

Reviews:

Brands by name

Popular brands