ABB IRB 390 Product Manual Download Page 272

Page: 272 / 346

Removing the universal joint

Note

Action

Torque wrench head, closed end:
3HAC063379-001.

xx2000000335

Remove the universal joint from the gear unit by
removing the screws and washers, using a special
torque wrench head.

Note

Keep the sealing ring and friction shim for refitting.

Refitting the motor and gear unit

Use these procedures to refit the axis-4 motor and gear unit.

Refitting the universal joint

Note

Action

Cleaning agent: Isopropanol.

Clean the friction shim, the sealing ring and the
contact surfaces with isopropanol. Inspect for
damage.

Friction shim: 3HAC060200-001.
Sealing ring: 3HAC060263-001.

Replace if damaged.

Continues on next page

272

Product manual - IRB 390

3HAC066566-001 Revision: B

5 Repair

5.6.4 Replacing the axis-4 gear unit pre-stage

Continued

Summary of Contents for IRB 390


























































































































































































































































































































































Search results

Summary of Contents for IRB 390

Reviews:

Brands by name

Popular brands

ABB IRB 390, Product Manual

Search results

Summary of Contents for IRB 390

Reviews:

Brands by name

Popular brands