manualshive.com logo in svg

ABB IRB 390, Product Manual

Share
Download
ABB IRB 390 Product Manual Download Page 206

Note

Action

DANGER

Turn off all:

•

electric power supply

•

hydraulic pressure supply

•

air pressure supply

to the robot, before entering the safeguarded
space.

2

Remove any loads or tools attached to the turning
disk.

3

Loosening the lower arm shafts

Note

Action

CAUTION

Make sure that all supplies for electrical power
are turned off.

1

Lashing strap

xx2000000334

CAUTION

The delta unit will become unstable when a lower
arm is removed.
Support the weight of the delta unit before remov-
ing the arm to minimize the movement. Either
support the weight from underneath or secure the
weight with a lashing strap through the universal
joints closest to the telescopic shaft.

2

Continues on next page

206

Product manual - IRB 390

3HAC066566-001 Revision: B

© Copyright 2020 - 2021 ABB. All rights reserved.

5 Repair

5.5.2 Replacing the upper arm

Continued

Summary of Contents for IRB 390



























































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands