ABB IRB 390 Product Manual Download

Page: 134 / 346

Note

Action

Make sure the roundsling has free
space and does not wear against
any part of the robot.

xx2000000920

Attach the roundslings to the lifting eyes and at-
tach to an overhead crane.

Note

Make sure the roundslings do not rub against any
sharp edges.

Raise the overhead crane to take the weight of
the robot.

xx2000000469

Remove the attachment screws and washers.

xx2000001110

Lift away the robot and place it on a suitable
working space for continuing the removal work.

Moving equipment from the old base to the new spare part

The base spare part has several possible configurations with included equipment.

Move equipment from the old base to the new spare part accordingly, before
refitting the base to the robot frame.

See detailed replacement procedures:

•

Replacing the SMB unit on page 161

Continues on next page

134

Product manual - IRB 390

3HAC066566-001 Revision: B

5 Repair

5.4.1 Replacing the base unit

Continued

Summary of Contents for IRB 390


























































































































































































































































































































































Search results

Summary of Contents for IRB 390

Reviews:

Related manuals for IRB 390

Brands by name

Popular brands

ABB IRB 390, Product Manual

Search results

Summary of Contents for IRB 390

Reviews:

Related manuals for IRB 390

Brands by name

Popular brands