ABB IRB 390 Product Manual Download

Page: 240 / 346

Note

Action

xx1900001837

Remove the cable bracket attachment screws.

xx2000001005

Snap loose the cable connectors from the cable
bracket and disconnect the motor cabling.

24 VDC power supply

To release the brakes, connect the 24 VDC power
supply.

Connect to R3.MP1/R3.MP2/R3.MP3-connector:

•

+ = pin 2

•

- = pin 5

xx1900000760

Remove two of the screws and washers securing
the motor.

Guide pin, M8x150: 3HAC15520-2

xx1900001835

Fasten two guide pins.

Tip

Lubricate the guide pins with some grease to
make the motor slide better.

Remove the two remaining screws and washers.

Continues on next page

240

Product manual - IRB 390

3HAC066566-001 Revision: B

5 Repair

5.6.1 Replacing the axis-1, axis 2 and axis-3 motor

Continued

Summary of Contents for IRB 390


























































































































































































































































































































































Search results

Summary of Contents for IRB 390

Reviews:

Related manuals for IRB 390

Brands by name

Popular brands

ABB IRB 390, Product Manual

Search results

Summary of Contents for IRB 390

Reviews:

Related manuals for IRB 390

Brands by name

Popular brands