ABB IRB 390 Product Manual Download

Page: 182 / 346

Reconnecting the cabling

Note

Action

xx1900001845

Connect the motor connectors and fasten the
connectors to the connector bracket by snapping
them into place.

Secure the cabling and connectors with cable ties.

xx1900001842

Refit the holder for connector R1.MP1.

Refitting the complete SMB unit

Note

Action

ELECTROSTATIC DISCHARGE (ESD)

The unit is sensitive to ESD. Before handling the
unit read the safety information in section

The

unit is sensitive to ESD on page 42

Secure the cables to connectors R2.FB1-4,
R2.FB5 (IRB 390 - 10/1300) with a cable tie at the
battery bracket.

xx2000002201

Connect the connectors:

•

R2.FB1-4, R2.FB5 (IRB 390 - 10/1300)

Continues on next page

182

Product manual - IRB 390

3HAC066566-001 Revision: B

5 Repair

5.4.4 Replacing the cable harness

Continued

Summary of Contents for IRB 390


























































































































































































































































































































































Search results

Summary of Contents for IRB 390

Reviews:

Related manuals for IRB 390

Brands by name

Popular brands

ABB IRB 390, Product Manual

Search results

Summary of Contents for IRB 390

Reviews:

Related manuals for IRB 390

Brands by name

Popular brands