ABB IRB 390 Product Manual Download

Page: 58 / 346

Moving the upper arms to installation position

Use this procedure to release the brakes and move the upper arms into installation
position.

Note

Action

+24V

(11)

(12)

xx2000000686

Supply power to connector R1.MP on the robot,
to be able to use the brake release button:

•

0V on pin 12.

•

24V on pin 11.

DANGER

Incorrect connections, such as supplying power
to the wrong pin, may cause all brakes to be re-
leased simultaneously and instantly!

Note

Do not interchange the 24V and 0V pins.
If they are mixed up, damage can be caused to
internal electrical components.

See

Releasing the brakes on

page 68

Release the brakes by pressing the brake release
button and move the upper arms to synchroniza-
tion position.

See

Synchronization marks and

synchronization position for axes
on page 300

xx2000000676

Disconnect the 24V supply from the R1.MP con-
nector.

Continues on next page

Product manual - IRB 390

3HAC066566-001 Revision: B

3 Installation and commissioning

3.3.5 Orienting, assembling and securing the manipulator

Continued

Summary of Contents for IRB 390


























































































































































































































































































































































Search results

Summary of Contents for IRB 390

Reviews:

Related manuals for IRB 390

Brands by name

Popular brands

ABB IRB 390, Product Manual

Search results

Summary of Contents for IRB 390

Reviews:

Related manuals for IRB 390

Brands by name

Popular brands