ABB IRB 390 Product Manual Download | Manualshive

Page: 68 / 346

background image

3.3.7 Manually releasing the brakes

Introduction to manually releasing the brakes

This section describes how to release the holding brakes for the axes motors.

Location of the brake release unit

The brake release unit is located as shown in the figure.

xx1900000252

Releasing the brakes

This procedure describes how to release the holding brakes when the robot is
equipped with a brake release unit.

Note

Action

The internal brake release unit is equipped with a
button for controlling the axes brakes.

Note

If the robot is not connected to the controller, power
must be supplied to the connector R1.MP according
to the section

Supplying power to connector R1.MP

.

1

DANGER

When releasing the holding brakes, the robot axes
may move very quickly and sometimes in unexpec-
ted ways.
Make sure no personnel is near or beneath the ro-
bot.

2

Continues on next page

68

Product manual - IRB 390

3HAC066566-001 Revision: B

© Copyright 2020 - 2021 ABB. All rights reserved.

3 Installation and commissioning

3.3.7 Manually releasing the brakes

«
...
66
67
68
69
70
...
»

Summary of Contents for IRB 390



























































































































































































































































































































































Reviews:

No comments

Related manuals for IRB 390

Brand: T.I.P. Pages: 48

Brand: MB&F Pages: 16

Brand: Kettler Pages: 32

Sloth Learning Kit

Brand: SunFounder Pages: 36

Brand: Marvelmind Pages: 26

Brand: 4M Pages: 2

Octopus Robotic Claw

Brand: 4M Pages: 2

Brand: SuperDroid Robots Pages: 6

Brand: Thames & Kosmos Pages: 68

Brand: UFactory Pages: 165

Brand: ABB Pages: 50

Brand: Jigabot Pages: 3

Brand: Bioloid Pages: 142

SC050 Battle Beasts

Brand: Sharper Image Pages: 24

Brand: Kondo Pages: 40

Brand: Kondo Pages: 56

Brand: Kondo Pages: 60

Brand: Kondo Pages: 71

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands