ABB IRB 390 Product Manual Download

Page: 210 / 346

Refitting the lower arm shafts

Note

Action

Sealing washer: 3HAC062123-001.

xx2000000861

Fit sealing washers to the lower arm.
Replace the sealing washers if damaged.

Anti-seize paste: 3HAC070875-002
(Molykote P1900)

xx2000000684

Lubricate the lower arm thread with grease.

Note

The surface under the thread head must be dry
and not contain grease.

Lower arm / parallel bar:
3HAC060138-001.

xx1900001802

Secure the lower arms including the sealing
washers to the upper arm.
Make sure the sealing washers are in place.

Continues on next page

210

Product manual - IRB 390

3HAC066566-001 Revision: B

5 Repair

5.5.2 Replacing the upper arm

Continued

Summary of Contents for IRB 390


























































































































































































































































































































































Search results

Summary of Contents for IRB 390

Reviews:

Related manuals for IRB 390

Brands by name

Popular brands

ABB IRB 390, Product Manual

Search results

Summary of Contents for IRB 390

Reviews:

Related manuals for IRB 390

Brands by name

Popular brands