ABB IRB 390 Product Manual Download

Page: 209 / 346

Note

Action

Upper arm: 3HAC060604-003.

Fit the upper arm to the base unit and secure with
12 attachment screws and washers.

Hex socket head cap screw: M8x40
Steel 12.9 Gle 603+Geo500 (12
pcs)
Washers, 12 pcs: 3HAC043799-001
(12 pcs)
Tightening torque: 35 Nm.

xx1900001800

Gasket: 3HAC058619-001.

xx1900001822

Check the upper arm cover gasket.
Replace if damaged.

Anti-seize paste: 3HAC070875-002
(Molykote P1900)

Lubricate the thread of the upper arm cover and
the gasket with grease.

Tightening torque: approximately
45 Nm.

Refit the upper arm cover including the gasket.

Tighten until the cover bottoms on
the upper arm.

xx1900001799

Continues on next page

Product manual - IRB 390

209

3HAC066566-001 Revision: B

5 Repair

5.5.2 Replacing the upper arm

Continued

Summary of Contents for IRB 390


























































































































































































































































































































































Search results

Summary of Contents for IRB 390

Reviews:

Related manuals for IRB 390

Brands by name

Popular brands

ABB IRB 390, Product Manual

Search results

Summary of Contents for IRB 390

Reviews:

Related manuals for IRB 390

Brands by name

Popular brands