ABB IRB 390 Product Manual Download Page 276

Page: 276 / 346

Note

Action

Rotating AC motor M104 with pin-
ion: 3HAC058581-003.

Lift the motor into the base.
Use the rotation tool to rotate the pinion when
mating it into the gear.

Rotation tool: 3HAB7887-1

xx2000001083

Hex socket head cap screw: M6x25
Steel 8.8-A2F (4 pcs).

Secure the unit with attachment screws and
washers.

Plain washer: 6.4x12x1.6 steel-A2F
(4 pcs).
Tightening torque: 10 Nm.

xx2000001082

Torx pan head screw: M6x12 Steel
8.8-A2F (4 pcs)

xx2000001031

Refit the cable bracket to the motor with four
screws.

Disconnect the 24 VDC power supply.

Continues on next page

276

Product manual - IRB 390

3HAC066566-001 Revision: B

5 Repair

5.6.4 Replacing the axis-4 gear unit pre-stage

Continued

Summary of Contents for IRB 390


























































































































































































































































































































































Search results

Summary of Contents for IRB 390

Reviews:

Brands by name

Popular brands

ABB IRB 390, Product Manual

Search results

Summary of Contents for IRB 390

Reviews:

Brands by name

Popular brands