ABB IRB 390 Product Manual Download Page 198

Page: 198 / 346

Required tools and equipment

Note

Article number

Equipment

Width 25 mm
Length 2.5 m

Lashing strap

Included in robot delivery.

xx1900002148

Used with an interchangeable
head torque wrench (not included
in delivery).
Interface: 14x18 mm.

3HAC073854-001

Torque wrench head, open-end in-
sert

Interchangeable head torque
wrench

Content is defined in section

Standard toolkit on page 336

Standard toolkit

Removing the lower arm

Use these procedures to remove the lower arm.

Preparations before removing the lower arm

Note

Action

The robot does not need to be jogged into any
specific position due to repair activity.

Do not move the position of the robot arms during
lower arm replacement.

DANGER

Turn off all:

•

electric power supply

•

hydraulic pressure supply

•

air pressure supply

to the robot, before entering the safeguarded
space.

Remove any loads or tools attached to the turning
disk.

Removing the lower arm

Note

Action

CAUTION

Make sure that all supplies for electrical power
are turned off.

Continues on next page

198

Product manual - IRB 390

3HAC066566-001 Revision: B

5 Repair

5.5.1 Replacing the lower arm

Continued

Summary of Contents for IRB 390


























































































































































































































































































































































Search results

Summary of Contents for IRB 390

Reviews:

Brands by name

Popular brands

ABB IRB 390, Product Manual

Search results

Summary of Contents for IRB 390

Reviews:

Brands by name

Popular brands