manualshive.com logo in svg

ABB IRB 390, Product Manual

Share
Download
ABB IRB 390 Product Manual Download Page 291

Refitting the axis-5 motor

Note

Action

O-ring: 3HAB3772-163.

xx2000001087

Check the o-ring.
Replace if damaged.

1

Guide pin, M6x150

If not already fitted, fit two guide pins to the motor
attachment holes.

2

Always use guide pins in pairs.

xx2000001092

24 VDC power supply

To release the brakes, connect the 24 VDC power
supply.

3

Connect to R3.MP5-connector:

•

+ = pin 2

•

- = pin 5

xx2000001032

•

4: Axis-4 motor

•

5: Axis-5 motor

The motors are oriented differently on the axis-4
and axis-5 gear unit assemblies, in regard to the
cable outlet on top.
Check that the motor is oriented according to the
figure before securing the unit, for each axis re-
spectively.

4

Continues on next page

Product manual - IRB 390

291

3HAC066566-001 Revision: B

© Copyright 2020 - 2021 ABB. All rights reserved.

5 Repair

5.6.5 Replacing the axis-5 gear unit pre-stage

Continued

Summary of Contents for IRB 390



























































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands