ABB IRB 390 Product Manual Download Page 219

Page: 219 / 346

Refitting the lower end of the telescopic shaft

Note

Action

CAUTION

The telescopic shaft must be oriented correctly,
otherwise it is damaged. Always fit the narrow
shaft part up against the base unit.

Cleaning agent: Isopropanol.

Clean the friction shim and sealing ring with isop-
ropanol.

Friction shim: 3HAC060200-001.

Inspect the friction shim and sealing ring. Replace
if damaged.

Sealing ring: 3HAC060263-001

xx1900001830

Fit the friction shim to the telescopic shaft lower
joint.

xx1900001826

Install the sealing ring at the lower joint and guide
the telescopic shaft into place.

CAUTION

Hold the telescopic unit carefully, the tube may
slide and get damaged.

Continues on next page

Product manual - IRB 390

219

3HAC066566-001 Revision: B

5 Repair

5.5.3 Replacing the telescopic shafts and universal joints

Continued

Summary of Contents for IRB 390


























































































































































































































































































































































Search results

Summary of Contents for IRB 390

Reviews:

Brands by name

Popular brands

ABB IRB 390, Product Manual

Search results

Summary of Contents for IRB 390

Reviews:

Brands by name

Popular brands