ABB IRB 390 Product Manual Download

Page: 277 / 346

Note

Action

xx1900001845

Connect the motor connectors and fasten the
connectors to the connector bracket by snapping
them into place.

Refitting the upper end of the telescopic shaft

Note

Action

Cleaning agent: Isopropanol.

Clean the friction shim, the sealing ring and the
contact surfaces with isopropanol. Inspect for
damage.

Friction shim: 3HAC060200-001.
Sealing ring: 3HAC060263-001

Replace if damaged.

Telescopic shaft unit:
3HAC059382-003

xx1900001825

Fit the upper end of the telescopic shaft by in-
stalling the friction shim, sealing ring and the
telescopic shaft at the joint.

CAUTION

The telescopic shaft must be oriented correctly,
otherwise it is damaged. Always fit the narrow
shaft part up against the base unit.

Continues on next page

Product manual - IRB 390

277

3HAC066566-001 Revision: B

5 Repair

5.6.4 Replacing the axis-4 gear unit pre-stage

Continued

Summary of Contents for IRB 390


























































































































































































































































































































































Search results

Summary of Contents for IRB 390

Reviews:

Related manuals for IRB 390

Brands by name

Popular brands

ABB IRB 390, Product Manual

Search results

Summary of Contents for IRB 390

Reviews:

Related manuals for IRB 390

Brands by name

Popular brands