background image

Removing the axis-2 motor

Note

Action

DANGER

Make sure that all supplies for electrical power,
hydraulic pressure, and air pressure are turned
off.

1

xx1800002488

Remove the swing support cover.

2

xx1800002489

Remove the connector plate.

CAUTION

Be aware of the cablings that are attached to the
connector plate! The connector plate cannot be
removed completely until the connectors are re-
move from the plate.

3

xx1800002490

Disconnect the connector.

J2.FB2

Tip

Take photos of the connector and cable position
before disconnecting them, to have as a reference
when reconnecting.

4

Continues on next page

504

Product manual - IRB 1100

3HAC064992-001 Revision: C

© Copyright 20192020 ABB. All rights reserved.

5 Repair

5.8.2 Replacing the axis-2 gearbox

Continued

Summary of Contents for IRB 1100









































































































































































































































































































































































































































































































































































































































Reviews: