YOKOGAWA AQ7280 OTDR Скачать руководство пользователя страница 174 | Manualshive

Страница: 174 / 195

background image

8-2

IM AQ7280-01EN

8.2 Error Messages

Error Messages

Messages may appear on the screen during operation. This section describes the error messages and
how to respond to them. Messages are displayed according to the language setting (see section 7.6).
If the corrective action states that serving is required, contact your nearest YOKOGAWA dealer.

In addition to the following messages, there are also communications error messages. These error
messages are described in the Communication Interface User’s Manual (IM AQ7280-17EN).

Error in Execution

Code

Message

20

Network Option is not installed.

21

Power Monitor Option is not installed.

22

Light source option is not installed.

24

One or more conditions in this file are not supported by this product.

27

The end point is different between acquired data and reference data. Please check the connected fiber cable.

28

The measurement may not be completed within the specified duration.

29

In remote control mode, all keys are locked except F1 key. Please hit F1 key to exit the remote control mode.

30

In Local Lockout mode, all keys are locked. Please cancel the local lockout.

33

File operation is cancelled.

35

The optical plug may not be connected securely.

36

Either of the analysis information below could not be retrieved. (Cursor info, Free marker info., Event info.)

37

The end point distance does not match with the master end point.

40

No more averaging is allowed. (already MAX averaging condition) Set "Average Continue"OFF for new

measurement.

41

Now updating firmware. Please wait. It takes approx. 20 seconds. Do not turn off power during update.

Restart automatically after successful updating.

46

A lot of files are saved in the root folder. The file manipulation slows when saved any further. Please make a folder

in the root folder, and save files in that.

47

Please start measurement after executing unchecking this fiber.

48

Now Logging. Please Wait.

49

ESC: Close the Touch Screen Test window, ENTER: Clear the display

60

Now Logging. Please Wait.

61

Logging process is completed. Please Save File.

62

Now adjusting LS power. Please wait.

63

LS power adjustment is completed.

64

Failed to adjust LS power. Please check whether the patch fiber cable is properly connected between LS port and

OPM port.

69

Optical fiber is found at the cursor position. Please stop the measure by pressing "REALTIME".

500

The measurement condition is failed. Please reset ****** in SETUP menu.

501

Not executable during measurement. Please stop the measurement and execute again.

502

The measurement cannot be started during printing. Please either wait until the end of the printing or interrupt the

printing.

503

The measurement cannot be started during the file operation. Please either interrupt the file operation or wait until

the end of the file operation.

504

The measurement could not be completed within the specified averaging duration. Please modify the averaging

duration.

505

Hardware failed, and needs to be repaired. Please contact Yokogawa's representatives.

506

Hardware failed, and needs to be repaired. Please contact Yokogawa's representatives.

507

Hardware failed, and needs to be repaired. Please contact Yokogawa's representatives.

508

Hardware failed, and needs to be repaired. Please contact Yokogawa's representatives.

509

Hardware failed, and needs to be repaired. Please contact Yokogawa's representatives.

510

PLUG CHECK Error. Please check or clean the connector.

511

This parameter is not valid in Simple (Full Auto) mode.

512

ZERO SET ERROR

«
...
172
173
174
175
176
...
»

Содержание AQ7280 OTDR




































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для AQ7280 OTDR

Бренд: ABQ Industrial Страницы: 15

Бренд: ABQINDUSTRIAL Страницы: 3

Бренд: Landis+Gyr Страницы: 26

Бренд: Landis+Gyr Страницы: 3

Бренд: NanoEnTek Страницы: 4

HF scientific AccUView LED

Бренд: Watts Страницы: 40

Бренд: Magnet-physik Страницы: 32

Бренд: MULTISPAN Страницы: 2

Instrument Control System

Бренд: Opus-Two Страницы: 8

Бренд: Magnescale Страницы: 2

Бренд: Datakom Страницы: 27

Бренд: Lafayette Instrument Страницы: 12

Бренд: DynAmp Страницы: 43

NEO MP18X Series

Бренд: MA Страницы: 3

Бренд: Seli Страницы: 68

Heinrichs Coriolis Mass Flow Meter

Бренд: Kobold Страницы: 118

Liquicap M FTI51

Бренд: Endress+Hauser Страницы: 96

VG-STRANDBERG V-BDN

Бренд: Boss Страницы: 15

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды