YOKOGAWA AQ7280 OTDR Скачать руководство пользователя страница 30

Страница: 30 / 195

2-5

IM AQ7280-01EN

Optical Pulse Measurement (OTDR)

Index

Setting Measurement Conditions in Detail Mode

Press the

Meas Setup

soft key to display the following screen.

When the screen is scrolled

Set the wavelength

(850nm, 1300nm, 1310nm,

1383nm, 1490nm, 1550nm, 1625nm, 1650nm).

Set the distance range

(Auto, 200m, 500m,

1km, 2km, 5km, 10km, 20km, 30km, 50km,

100km, 200km, 300km, 400km, 512km).
Set the pulse width

(Auto, 3ns, 10ns, 20ns,

30ns, 50ns, 100ns, 200ns, 300ns, 500ns,

1μs, 2μs, 5μs, 10μs, 20μs).

Set the high SNR mode (OFF, ON).
Set the sample interval (Normal, High Resolution).
Set the attenuation

(Auto, 0.00dB, 2.50dB,

5.00dB, 7.50dB, 10.00dB, 12.50dB, 15.00dB,

17.50dB, 20.00dB, 22.50dB, 25.00dB, 27.50dB,

30.00dB).

Executes initialization

Press to reset the measurement settings to

their factory defaults.

Set the average method (Hi-Speed, Hi-Reflection).
Set the average unit (Duration, Times).
When the average unit is set to Duration:

Set the average duration (Auto, 5sec, 10sec, 20sec,

30sec, 1min, 3min, 5min, 10min, 20min, 30min).
When the average unit is set to Times:

Set the average count (Auto, 2^10, 2^11, 2^12,

2^13, 2^14, 2^15, 2^16, 2^17, 2^18, 2^19, 2^20).

Set the fiber-in-use alarm (OFF, ON).
Set the connection check (OFF, ON).
Set the event search (Auto, Manual).

Set auto save (OFF, ON).

1 The available options vary depending on the OTDR unit.

Wavelength

The wavelengths set in Wavelength 1 to Wavelength 4 are measured one at a time (multi

wavelength measurement). You can set only the wavelengths of the same OTDR port.

For the wavelengths that you can set, see page 2-2.

2.1 Setting the Measurement and Analysis Conditions

Содержание AQ7280 OTDR




































































































































































































Результаты поиска

Содержание AQ7280 OTDR

Отзывы:

Похожие инструкции для AQ7280 OTDR

Бренды по названию

Популярные бренды

YOKOGAWA AQ7280 OTDR, Руководство пользователя

Результаты поиска

Содержание AQ7280 OTDR

Отзывы:

Похожие инструкции для AQ7280 OTDR

Бренды по названию

Популярные бренды