YOKOGAWA AQ7280 OTDR Скачать руководство пользователя страница 96 | Manualshive

Страница: 96 / 195

background image

4-3

IM AQ7280-01EN

Optical

Pulse Analysis

1

2

3

4

5

6

7

8

Index

• Distance Reference

Normally, the location where the AQ7280 and the optical fiber cable are connected is the

measurement reference point. This reference point is the distance reference. It is used to
calculate the distance to the cursor and markers. If you are using a launch fiber to perform
measurements, move the distance reference the length of the launch fiber before performing
measurements.

Distance reference

• Cursor Link (Moving all markers together)

You can move all markers while maintaining the distance between them.

4 Point Markers

Press the

4 Point Markers

soft key to display the following screen.

Sets marker .

Marker is set at the cursor

position.

1

1

Sets marker .

Marker is set at the cursor

position.

2

2

Cursor link

See 2 Point markers.

Set marker Y2.

Marker Y2 is set at the cursor

position.

Sets marker .

Marker is set at the cursor

position.

3

3

Press to set all

markers together.

3

Marker

Marker Y2

1

Marker

2

Marker

Marker information

When no cursors are set,

this becomes the ALL soft key.

Note

• Set the markers in the order shown above, starting with the measurement start point (the distance

reference).

• The measured loss value differs depending on the specified approximation method.
• Set the correct position for

2

. The splice loss changes greatly depending on the position of

2

.

4.1 Analyzing Waveforms

«
...
94
95
96
97
98
...
»

Содержание AQ7280 OTDR




































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для AQ7280 OTDR

Бренд: Farfisa Страницы: 14

Бренд: Valmet Страницы: 63

Бренд: Lambrecht Страницы: 5

Бренд: Keithley Страницы: 25

Бренд: Panasonic Страницы: 72

KW9M Eco-Power Meter

Бренд: Panasonic Страницы: 2

Бренд: LaMotte Страницы: 2

Бренд: Lampa Страницы: 12

Бренд: Velleman Страницы: 96

Бренд: ADA INSTRUMENTS Страницы: 27

Бренд: DeltaOHM Страницы: 26

Бренд: UEi Страницы: 5

Бренд: Kipp & Zonen Страницы: 32

Бренд: Hanna Instruments Страницы: 12

Бренд: AKCP Страницы: 16

Бренд: Swann Страницы: 106

Бренд: PANCONTROL Страницы: 157

Бренд: LaMotte Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды