YOKOGAWA AQ7280 OTDR Скачать руководство пользователя страница 175

Страница: 175 / 195

8-3

IM AQ7280-01EN

Troubleshooting, Maintenance, and Inspection

Index

Code

Message

513

ZERO SET ERROR

514

Exceeding limit. It may cause damage of the instrument. Please disconnect the plug.

515

ZERO SET ERROR

516

Fiber In Use Alarm Error 1

517

Fiber In Use Alarm Error 2

518

ZERO SET ERROR

519

ZERO SET ERROR

520

Hardware failed, and needs to be repaired. Please contact Yokogawa's representatives.

521

Operation is stopped outside of operating environmental condisions

522

Hardware failed, and needs to be repaired. Please contact Yokogawa's representatives.

524

Failure to initialize the option module.

525

The Interval is too short. Please change the inteval value.

526

Please set Avg Duration.

527

Need the AC power supply to measure. Please connect the AC adapter.

528

Free space is not enough. Please set the interval or the period again.

550

The event list does not exist in either of trace or both.

551

Measurement range of those two traces are not same reference points. Please set the origin (0m).

552

Fiber lengths do not match. The end point distance error between two traces must be within 3%.

553

Total number of events exceeds 100 for the 2-way analysis.

554

2-Way Trace cannot be executed due to difference in wavelengths of those two traces.

555

The differential trace cannot be created. Trace conditions are not same.

556

The differential trace cannot be created. No trace data available.

557

The differential trace cannot be created. The sampling resolutions are not same.

558

The differential trace cannot be created. The group indices are not same.

559

The differential trace cannot be created. The start points are not same.

560

When the event fix is ON, the distance reference setup cannot be performed.

561

has not been set. This function is effective only when

is set.

562

n-E has not been set. This function is effective only when n-E is set.

563

Conditions of the macro bending do not match.

601

Cannot save onto the media. This media is for read-only.

602

Can not recognize file system. -Internal memory: Contact Yokogawa's representatives. - USB memory or SD

card: Try the other media or format again with FAT

604

Storage media has been disconnected while the media is being accessed.

605

Same file name or folder name exists.

608

Invalid file name or folder name

609

Invalid file format

612

Invalid path name

614

Unknown file or folder

616

Cannot save onto the media. This media is for read-only.

620

Free space is not enough.

622

Unknown folder

623

Folder is not empty.

629

Writing to USB memory or SD card is not allowed.

634

Failed to delete the folder. Please confirm the following. - Media is correctly installed. - Media is formatted. -

Media is not read-only.

635

Failed to delete the folder. The path name or the file name is too long.

636

Failed to delete the folder. The hierarchy below the specified folder is too deep.

637

Failed to delete the folder. The path name is invalid.

638

The folder could not be deleted. Failed to delete files in the folder. Please confirm the following. - Media is correctly

installed. - Media is formatted. - Media is not read-only.

639

Failed to copy the folder. Please confirm the following. - Media is correctly installed. - Media is formatted. - Media

is not read-only.

640

Folder cannot be copied. The path name or the file name is too long.

641

Failed to copy the folder. The hierarchy below the specified folder is too deep.

642

Failed to copy the folder. The path name is invalid.

643

The folder copy could not be completed. Failed to create a destination folder. Please confirm the following.

- Media is correctly installed. - Media is formatted. - Media is not read-only.

644

The folder copy could not be completed. Failed to copy the files in the folder. Please confirm the following.

- Media is correctly installed. - Media is formatted. - Media is not read-only.

645

The path name is too long.

646

USB memory or SD card can not be recognized.

8.2 Error Messages

Содержание AQ7280 OTDR




































































































































































































Результаты поиска

Содержание AQ7280 OTDR

Отзывы:

Похожие инструкции для AQ7280 OTDR

Бренды по названию

Популярные бренды

YOKOGAWA AQ7280 OTDR, Руководство пользователя

Результаты поиска

Содержание AQ7280 OTDR

Отзывы:

Похожие инструкции для AQ7280 OTDR

Бренды по названию

Популярные бренды