YOKOGAWA AQ7280 OTDR Скачать руководство пользователя страница 130

Страница: 130 / 195

5-11

IM AQ7280-01EN

Optical Output and Optical Power Measurement

Index

Measuring Optical Power Using the Power Checker (/PC option

of the OTDR unit)

Making Preparations for Measurements

Remove the optical fiber cables from the AQ7280 and close the optical connector covers, or make sure

that the OTDR port is not receiving any light, and then start the power checker zero-set procedure.

Performing Zero-Set

From the top menu, select

Power Checker

to display the following screen.

Sets the reference to the currently

displayed measured value

Measured value

Bar graph display of

the measured value

See page 5-3.

Set the wavelength (1310nm,

1490nm, 1550nm, 1625nm, 1650nm).

Set the unit (dB, dBm, W).

Performs zero set

Upper threshold line

Lower threshold line

Lines showing the upper

and lower threshold values

Set the reference (–80 to 40 dBm).

The Reference box appears if you

press the DREF soft key or set the

unit to dB.

Execute

zero-set

Note

• Perform a zero-set whenever necessary, such as after you have turned on the power or when the ambient

temperature changes. Performing a zero-set adjusts the internal deviation of the power checker section
and enables you to obtain more accurate absolute optical power values.

• You can also start the power checker feature from the OTDR display screen. For the procedure, see

section 2.10.

Setting the Screen Display and Measurement Conditions

Setting the Wavelength

Measurement light with the following wavelengths can be measured.
1310nm, 1490nm, 1550nm, 1625nm, 1650nm

Note

This is not available on port 2 of the AQ7283E and AQ7283F, or on the AQ7282M.

5.2 Measuring Optical Power (OPM, /PC option)

Содержание AQ7280 OTDR




































































































































































































Результаты поиска

Содержание AQ7280 OTDR

Отзывы:

Похожие инструкции для AQ7280 OTDR

Бренды по названию

Популярные бренды

YOKOGAWA AQ7280 OTDR, Руководство пользователя

Результаты поиска

Содержание AQ7280 OTDR

Отзывы:

Похожие инструкции для AQ7280 OTDR

Бренды по названию

Популярные бренды