manualshive.com logo in svg

YOKOGAWA AQ7280 OTDR, Руководство пользователя

YOKOGAWA AQ7280 OTDR - высокоточный оптический тестер с возможностью измерения длины волоконных линий и нахождения точек поломки. Получите Руководство по началу работы бесплатно на manualshive.com, чтобы ознакомиться с возможностями этого инструмента. Легко загружайте руководства по эксплуатации и начинайте использовать свой устройство.

Поделиться
Скачать
background image

7-7

IM AQ7280-01EN

System Configuration

1

2

3

4

5

6

7

8

Index

Port Forwarding (UPnP)

UPnP Port Forwarding

  If the AQ7280 is connected to a network through a router with a NAT function, the AQ7280 cannot 

be controlled from a PC over the router. The AQ7280 has a function for transferring data with 
routers with a NAT function that support Universal Plug and Play (UPnP). When this function is 
enabled, the AQ7280 can be controlled from a PC over a router. This function is called UPnP port 
forwarding.

  ON:  The UPnP port forwarding function is enabled.
  OFF: The UPnP port forwarding function is disabled.

Status

  Displays the communication status between the AQ7280 and a UPnP compatible NAT router.
  ---: 

The UPnP port forwarding is disabled.

  Normal: 

 Configuration required for port forwarding is complete between the AQ7280 and 
router.

  Setting: 

Port forwarding is being configured.

  Set up failure:  Port forwarding cannot be configured.
  Router searching failure:
   

A UPnP compatible NAT router could not be found.

URL

  Displays the URL of the UPnP compatible NAT router. Enter this URL in the PC browser when 

controlling the AQ7280 from the PC.

  --:   The UPnP port forwarding is disabled. Or, the status is not showing Normal.
 http://xxx.xxx.xxx.xxx:8080/:
      The IP address of the router’s WAN port is shown in x. 8080 is a fixed port number.

WAN IP Address

  Displays the IP address of the UPnP compatible NAT router.
  --:   The UPnP port forwarding is disabled. Or, the status is not showing Normal.
 xxx.xxx.xxx.xxx:
      The IP address of the router’s WAN port is shown in x.

Refresh Screen

  Refreshes the status, URL, WAN IP address information.
  The AQ7280 communicates with a UPnP compatible NAT router at 1 minute intervals to update the 

port forwarding settings. Clicking Refresh Screen displays the current port forwarding settings.

Note

•  If port number 8080 of the UPnP compatible NAT router is used by another service, the UPnP port 

forwarding function cannot be used.

•  The UPnP port forwarding function cannot be used on some UPnP compatible NAT routers if the transport 

destination and source numbers are not the same. The port number that the AQ7280 uses for UPnP port 
forwarding destination is 80.

•  Depending on the UPnP compatible NAT router, the UPnP port forwarding function may be disabled. In 

such a case, enable the function.

7.4  Configuring Network Settings (/LAN option)

Содержание AQ7280 OTDR




































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для AQ7280 OTDR

Kawai CN35 Software Update preview
CN35
Бренд: Kawai Страницы: 2
F.W. Bell 5200 Series Instruction Manual preview
5200 Series
Бренд: F.W. Bell Страницы: 75
D-tect Systems rad-DX Installation And Operating Instructions Manual preview
rad-DX
Бренд: D-tect Systems Страницы: 19
M-system 47LCT Operating Manual preview
47LCT
Бренд: M-system Страницы: 16
M-system 73VR3100 Startup Manual preview
73VR3100
Бренд: M-system Страницы: 25
Macherey-Nagel NANOCOLOR Advance Operating Instruction preview
NANOCOLOR Advance
Бренд: Macherey-Nagel Страницы: 45
Ulvac SPU Instruction Manual preview
SPU
Бренд: Ulvac Страницы: 24
Valhalla Scientific 4300B Operation Manual preview
4300B
Бренд: Valhalla Scientific Страницы: 43
Keithley 6517A User Manual preview
6517A
Бренд: Keithley Страницы: 343
Keithley 6514 Instruction Manual preview
6514
Бренд: Keithley Страницы: 334
La Crosse Technology EA-3010 Operating Manual preview
EA-3010
Бренд: La Crosse Technology Страницы: 2
PANCONTROL PAN 118 Manual preview
PAN 118
Бренд: PANCONTROL Страницы: 157
Sensitech FreezeAlert Instructions For Use preview
FreezeAlert
Бренд: Sensitech Страницы: 2
Artistic License Commissioner dali User Manual preview
Commissioner dali
Бренд: Artistic License Страницы: 26
Oceanic DATATRANS Owner'S Manual preview
DATATRANS
Бренд: Oceanic Страницы: 114
Calculated Industries LaserDIMENSIONMASTER 3336 User Manual preview
LaserDIMENSIONMASTER 3336
Бренд: Calculated Industries Страницы: 2
IS Technologies SLM1200S User Manual preview
SLM1200S
Бренд: IS Technologies Страницы: 21
Mityvac MV5532 User Manual preview
MV5532
Бренд: Mityvac Страницы: 24

Бренды по названию

Популярные бренды

Загрузить еще бренды