YOKOGAWA AQ7280 OTDR Скачать руководство пользователя страница 177

Страница: 177 / 195

8-5

IM AQ7280-01EN

Troubleshooting, Maintenance, and Inspection

Index

Code

Message

803

FTP Error : Rm Please confirm network connection and setting.

804

FTP Error : List Please confirm network connection and setting.

805

FTP Error : Mkdir Please confirm network connection and setting.

806

FTP Error : Rmdir Please confirm network connection and setting.

807

FTP Error : Get Please confirm network connection and setting.

808

FTP Error : Put Please confirm network connection and setting.

809

FTP Error : GetData Please confirm network connection and setting.

810

FTP Error : PutData Please confirm network connection and setting, and desk capacity.

811

FTP Error : AppedData Please confirm network connection and setting, and desk capacity.

812

FTP Error : Client Handle Please confirm network connection and setting.

813

FTP Error : Others Please confirm network connection and setting.

814

Failed network initialize. Please confirm network connection and setting.

815

Different passwords are entered. Please try again.

817

Test Error occurred.

818

Test succeeded.

819

ROM Test Error occurred.

820

RAM Test Error occurred.

821

System File Test Error occurred.

822

Battery Test Error occurred.

823

Temperature Test Error occurred.

854

In USB Storage mode, all keys are locked. Please disconnect the USB Cable.

855

While a measurement is progressed or a file is accessed, it cannot go to USB storage mode. Please try again after

stopping a measurement or a file access.

900

Backup data is damaged. this instrument starts up with the factory setting.

901

Optical connector is not correctly connected. Please clean and reconnect the connector again.

902

Battery is low Please power it off, and charge the battery or replace the battery. Or, please use the AC power

supply.

903

Backup battery failed, and needs to be repaired. Please contact Yokogawa's representatives.

904

Hardware failed, and needs to be repaired. Please contact Yokogawa's representatives.

905

Battery error. Please replace the battery.

906

Battery is low The instrument will be powered off in 10 sec.

907

Battery temperature is too high. The instrument will be powered off in 10 sec. Please turn off power to cool battery

908

Battery temperature is too low. The instrument may be damaged if used in this condition. The instrument will be

powered off in 10 sec. Please turn off power and use battery with proper operating temperature.

909

The temperature inside the instrument is too high. The instrument may be damaged if used in this condition. The

instrument will be powered off in 10 sec. Please turn off power to allow instrument to cool down.

910

The temperature inside the instrument is too low. The instrument may be damaged if it is used in this condition.

The instrument will be powered off in 10 sec. Please turn off power until internal temperature is increased.

911

The Voltage of AC power supply is too low. The instrument may be damaged if it is kept using in this condition.

The instrument will be powered off in 10 sec. Please make sure of using the dedicated AC adapter.

912

The Voltage of AC power supply is too high. The instrument may be damaged if it is kept using in this condition.

The instrument will be powered off in 10 sec. Please make sure of using the dedicated AC adapter.

913

Battery is low. The instrument may be damaged if it is kept using in this condition. The instrument will be powered

off in 10 sec. Please use AC adapter.

914

Errors in the battery or in the charging circuit. The instrument may be damaged if it is kept using in this condition.

The instrument will be powered off in 10 sec. Please remove the battery and use AC adapter.

915

Battery temperature is too high. Please stop measuring, and wait for a while.

916

Battery temperature is too high. The measurement was aborted. Please power it off.

917

The temperature inside the instrument is increasing. Please stop measuring, and wait for a while.

918

The temperature inside the instrument is too high. The measurement was aborted. Please power it off.

919

Non-standard battery is connected. The instrument may be damaged if it is kept using in this condition. The

instrument will be powered off in 10 sec. Please replace the battery.

921

There is incoming light. Or, optical module may be damaged.

922

Incorrect date and time setting. Set the correct date and time.

923

The ambient temperature is out of range. The light source cannot be turned on.

925

Please use AC adapter.

8.2 Error Messages

Содержание AQ7280 OTDR




































































































































































































Результаты поиска

Содержание AQ7280 OTDR

Отзывы:

Похожие инструкции для AQ7280 OTDR

Бренды по названию

Популярные бренды

YOKOGAWA AQ7280 OTDR, Руководство пользователя

Результаты поиска

Содержание AQ7280 OTDR

Отзывы:

Похожие инструкции для AQ7280 OTDR

Бренды по названию

Популярные бренды