YOKOGAWA AQ7280 OTDR Скачать руководство пользователя страница 182

Страница: 182 / 195

8-10

IM AQ7280-01EN

Note

• The pass/fail judgment function is supported only by the following fiber inspection probes.

DI-1000 (Lightel)
DI-1000L (Lightel)

• Pass/fail judgment complies with IEC 61300-3-35.

Configuring the Pass/Fail Judgment

Press

SETUP

to display a fiber end face pass/fail setup screen.

Select the optical fiber cable (SM, MM).

Turn judgment execution on or off

Set the scratch or defect judgment

threshold values (No Limit, 0 to 100).

Displays the results.

Returns to step 3

System configuration

See chapter 7.

Select the judgment reference.

When the optical fiber cable selection is

SM: UPC, SPC, APC

MM: Default

When configuration is complete, press ESC to return to the fiber inspection probe screen.

Executing Pass/Fail Judgments

Press the

Judge Enable

soft key. Executes pass/fail judgment and displays the judgment

results (summary). Before executing pass/fail judgment, adjust the fiber inspection probe knob
to focus on the image.

Clear

Clears the judgment

results.

Displays results

The judgment results

(details) are displayed.

Saves data

Press this soft key to

save a still image and a

judgment result file. For

the procedure to set the

file save destination, file

type, and file name, see

section 6.3.

Core

Cladding

Contact

Judgment results (summary)

Appears when pass/fail judgment is performed.

Optical fiber cable type

Appears at all times for still images.

8.6 Checking the Optical Fiber End Face for Stains

Содержание AQ7280 OTDR




































































































































































































Результаты поиска

Содержание AQ7280 OTDR

Отзывы:

Похожие инструкции для AQ7280 OTDR

Бренды по названию

Популярные бренды

YOKOGAWA AQ7280 OTDR, Руководство пользователя

Результаты поиска

Содержание AQ7280 OTDR

Отзывы:

Похожие инструкции для AQ7280 OTDR

Бренды по названию

Популярные бренды