YOKOGAWA AQ7280 OTDR Скачать руководство пользователя страница 37

Страница: 37 / 195

2-12

IM AQ7280-01EN

Advanced Analysis

• Pass Fail Judgement

Using the

rotary knob

and

ENTER

, set Pass Fail Judgement to

Setup[OFF]

Setup[ON]

. The

following screen appears.

Set the judgment (Hide, Display).

Set the splice loss threshold

(0.01dB to 9.99dB).

Set the return loss threshold

(20dB to 70dB).

Set the splitter loss threshold

(1.0dB to 20.0dB).

Set the dB/km loss threshold

(0.01dB to 9.99dB).

Set the total loss

threshold (1dB to 65dB).

Set the preset (UserDefine,

Preset 1, Preset 2, Preset 3).

Turns the pass fail judgment on

or off.

Set the connector loss

threshold (0.01dB to 9.99dB).

Pass Fail Judgement

A judgment is performed on the events detected in the target waveform, and those that exceed

the specified threshold are displayed as fault events.

ON: Events that have exceeded their thresholds are displayed with an asterisk attached to

them.

OFF: Events that have exceeded their thresholds are not displayed with an asterisk attached

to them.

Judgment

  The judgment information is displayed in the lower left of the AQ7280 screen.
  Display:   The number of fault events, total loss, and total return loss are displayed.
  Hide:     The judgment information is not displayed.

Events judged as Fail

Judgment display

2.1 Setting the Measurement and Analysis Conditions

Содержание AQ7280 OTDR




































































































































































































Результаты поиска

Содержание AQ7280 OTDR

Отзывы:

Похожие инструкции для AQ7280 OTDR

Бренды по названию

Популярные бренды

YOKOGAWA AQ7280 OTDR, Руководство пользователя

Результаты поиска

Содержание AQ7280 OTDR

Отзывы:

Похожие инструкции для AQ7280 OTDR

Бренды по названию

Популярные бренды