Toshiba Strata DK 24, Руководство по установке и обслуживанию

Страница: 211 / 372

8-41
INSTALLATION-PERIPHERALS
SECTION 400-096-208
SEPTEMBER 1992
Programming Considerations
10.31 Voice mail (VM) PSTU or PESU port pro-
gramming is accomplished using Programs 31
and 10-2. (Refer to Programming Procedures,
Section 400-096-300, for more details.) VM pro-
gramming features are as follows:
•
VM Groups—This feature groups VM PSTU or
PESU ports together so that message waiting
set/cancel signals appear to originate from the
lowest port in the VM group. All VM ports con-
nected to a particular VM machine should be set
in the
same VM group (Program 31, LEDs 05 ~
08).
•
Message Waiting (MW) Set/Cancel—If the VM
machine has the ability to dial a code and the
appropriate station numbers to set or cancel the
message waiting LEDs on digital and electronic
telephones, program the VM machine to dial the
following sequences (Program 10-2, LED 04):
1) To set a MW LED, the VM machine must
dial 6 3 + station number.
2) To cancel a MW LED, the VM machine
must dial 6 4 + station number.
NOTE:
Only dial codes 6 3 and 6 4 are set in the VM
device configuration; the VM device will dial
the station number automatically to set/cancel
the MW LED.
•
No Conference VM—Prevents undesired
three-party connections during VM call trans-
fers. All VM ports should be set for No Confer-
ence (Program 31, LED 09).
•
Privacy Override Deny—Prevents stations from
overriding (breaking in) in-progress VM calls
(Program 31, LED 18).
•
End-to-End Signaling—Allows VM port Dual-
tone Multi-frequency (DTMF) operation. All VM
ports should be set for end-to-end signaling
(Program 31, LED 17).
NOTE:
The CRCU (-4 or -8) must be installed on the
PCTU or PCTUS to allow End-to-End Signal-
ing.
•
Receive Auto Call Forward ID Codes—Pro-
vides auto digits from call forwarded stations to
direct callers to station mailboxes. All VM ports
should be set to receive auto ID code (Program
31, LED 16).
10.32 Voice Mail Program Checklist. The follow-
ing items should be verified before programming
voice mail:
1) Set Toshiba VP Maintenance Menu system
parameters to “D” = STRATA DK (see Toshiba
VP documentation for other parameter set-
tings).
2) STRATA DK programs:
•
Program 92: Initialization clears voice mail
auto dial codes.
•
Program 03: Verify that a CRCU (-4 or -8) is
installed on the PCTU to allow the VM device
to send DTMF tones.
•
Program 04: Assigns station numbers to
VM ports (initialized numbers recom-
mended).
•
Program 05: First digit of special codes 6 3
and 6 4 (initialized numbers recommended).
•
Program 10-1: Set the system for voice
first, and program the VM device to dial the
suffix as “1” after station numbers.
•
Program 10-2: Set LED 04 ON for set/can-
cel operation and LED 06 ON for the VM to
detect 80 millisecond tones.
•
Program 13: If the VM device is the mes-
sage center, set the lowest VM port as the
message center.
•
Program 31: Turn LEDs 04, 05, 09, and 15
~ 20 ON for the PESU or PSTU ports that are
connected to the Toshiba VP ports. Do not
set these options for telephone station ports.
NOTE:
A, D, and B Tones should be enabled only for
VM devices that respond to these tones.
•
Program 33: Set the PESU and PSTU
ports that are connected to the VM
ports to a hunting sequence, starting with
the lowest port hunting to the next highest
port, etc. The last hunt should be to an
attendant station.