Timewave PK-900 Скачать руководство пользователя страница 231

Страница: 231 / 392

________________________________________________________________________________

HBaud "n/n" Default: 1200/1200 bauds

Mode: Packet Host: HB

_________________________________ Parameters: __________________________________

"n" - values specifying the Packet data rate in bits per second from each

Radio Port of the PK-900 to the radio.

________________________________________________________________________________

HBAUD sets the radio ("on-air") baud rate only in the Packet operating mode for

each Radio Port. The default is 1200 bits/sec (VHF) for Radio Port 1 and 0

(disabled) on Radio Port 2.

HBAUD has no relationship to your computer terminal program's baud rate.

Available HDLC packet data rates "n" include 45, 50, 57, 75, 100, 110, 150, 200,

300, 400, 600, 1200, 2400, 4800 and 9600 bauds.

________________________________________________________________________________

HEAderln ON|OFF Default: ON

Mode: Packet Host: HD

_________________________________ Parameters: __________________________________

ON - The header in a monitored packet is printed on a separate line from

the text.

OFF - The header and text of monitored packets are printed on the same line.

________________________________________________________________________________

When HEADERLN is ON (default), the address is shown, followed by a <CR><LF> that

puts the packet text on a separate line as shown below:

WX1AAA>WX2BBB:

Go ahead and transfer the file.

HEADERLN affects the display of monitored packets. When HEADERLN is OFF, the

address information is shown on the same line as the packet text as shown below:

WX1AAA>WX2BBB: Go ahead and transfer the file.

1/93 A-53

Содержание PK-900









































































































































































































































































































































































































Результаты поиска

Содержание PK-900

Отзывы:

Похожие инструкции для PK-900

Бренды по названию

Популярные бренды

Timewave PK-900, Руководство по эксплуатации

Результаты поиска

Содержание PK-900

Отзывы:

Похожие инструкции для PK-900

Бренды по названию

Популярные бренды