Timewave PK-900 Скачать руководство пользователя страница 115

Страница: 115 / 392

CHAPTER 7

AMTOR AND NAVTEX OPERATION

7.1 Overview

The PK-900 provides AMTOR (AMateur Teletype Over Radio) operation on

Radio Port 1 in accordance with FCC Part 97.69 and CCIR

Recommendations 476 and 625 for Mode A (ARQ) and Mode B (FEC). AMTOR

is an adaptation of the SITOR (ShIp Teletype Over Radio) system used

in high-seas telex, which provides error detection and correction.

AMTOR has two basic modes of operation, Mode A (ARQ - Automatic

ReQuest for Reception) and Mode B (FEC - Forward Error Correction).

o ARQ AMTOR is a handshaking protocol that allows only two stations

to communicate in a near error free fashion. You will hear a

"chirp chirp" sound when you find two stations conversing in ARQ.

PACTOR can be distinguised from AMTOR in that is uses a longer

(about 1 sec) data burst.

o FEC AMTOR is similar to Baudot RTTY and is used to call CQ or to

carry on "round table" contacts.

NAVTEX (NAVigational TEleX) is a form of FEC AMTOR that is used to

send Navigational bulletins and weather information primarily to ships

at sea. Recently it has been adopted by the ARRL to send bulletins to

amateurs.

7.2 Where to Operate AMTOR

Before you can operate AMTOR, you must first know where the activity

ocurrs. Most AMTOR operation occurs on the 20-meter amateur band

between 14.065 and 14.085 MHz. AMTOR activity can be found on the

other HF amateur bands as well and is most often located between 65

and 90 kHz up from the bottom of the band as it is on 20 meters.

7.2.1 PK-900 AMTOR Parameter Settings

AMTOR is a bit more complex than Baudot or ASCII operation. AMTOR

operating modes require SELCALL (Selective Call) codes be entered

before you can operate. There are two SELCALLs you should enter.

7.2.2 Entering Your SELective CALling Code (MYSELCAL)

This unique character sequence contains four alphabetic characters

that are derived from your call sign. The PK-900 automatically does

this for you just by entering your amateur callsign into the MYSELCAL

command. If you are using an AEA PAKRATT program, follow the

instructions in the program manual for entering the command MYSELCAL.

If you are using a terminal, then Type "MYSELCAL" to load your SELCALL

into the PK-900 as shown below:

cmd:MYSELCAL N7ML

1/93 7-1

Содержание PK-900









































































































































































































































































































































































































Результаты поиска

Содержание PK-900

Отзывы:

Timewave PK-900, Руководство по эксплуатации, Страница: 115 / 392

Результаты поиска

Содержание PK-900

Отзывы: