Timewave PK-900 Скачать руководство пользователя страница 21

Страница: 21 / 392

Figure 2-2 PK-900 Rear Panel Connections and Controls

2.3 Connecting Your Computer or Computer Terminal

MAKE SURE THE PK-900 AND YOUR COMPUTER ARE SWITCHED OFF

o Locate the PK-900 Serial Cable. Connect the 25-pin Female

connector to the RS-232 connector on the PK-900 rear panel.

o Connect the other end of this cable (Female DB-25) to the RS-232

Serial Port of your personal computer or Computer Terminal.

Details on connecting to common machines are listed below.

NOTE: This cable was designed to connect directly to a 25-pin IBM-PC

compatible RS-232 port. Many machines on the market today support

this configuration. Some less-common machines are listed in section

2.6. Please be certain you have properly connected the PK-900 to

your RS-232 computer or Terminal then proceed to section 2.4.

2.3.1 IBM-PC/XT/AT and Compatibles

IBM compatible 25-pin RS-232 serial ports should connect directly to

the supplied serial cable. Some IBM compatible machines are equipped

with a 9-pin serial port. For these machines a DB-9 to DB-25 adapter

should be obtained from a Radio Shack store or a computer dealer.

2.3.2 Apple Macintosh Series of Computers

AEA presently sells the program MacRATT with FAX which contains the

serial cable for the newer models of the Macintosh (models Mac + and

later). If you intend to use another communications program with the

PK-900 a Modem adapter cable must be purchased from your Apple

dealer to connect the Mac to your PK-900. For the newer machines

such as the Mac +, Mac SE and Mac II, a mini-8 to DB-25 adapter cable

is required (included with the AEA MACRATT with FAX program). For the

older Mac 128 and 512 machines, a DB-9 to DB-25 adapter cable from

your Apple dealer is needed.

2.3.3 Commodore 64 and 128 Computers

The Commodore 64/128 computers do not have an RS-232 port as standard

equipment. For these machines RS-232 adapters are available from

manufacturers such as Commodore or OMNITRONIX. These may work with

modem or terminal programs for your Commodore. Section 2.4 of this

chapter deals more with programs for personal computers. The AEA

Program COM-PAKRATT With FAX is NOT recommended for the PK-900.

1/93 2-3

Содержание PK-900









































































































































































































































































































































































































Результаты поиска

Содержание PK-900

Отзывы:

Timewave PK-900, Руководство по эксплуатации, Страница: 21 / 392

Результаты поиска

Содержание PK-900

Отзывы: