Timewave PK-900 Скачать руководство пользователя страница 137

Страница: 137 / 392

CHAPTER 8

MORSE OPERATION

8.1 Overview

The PK-900 will both send and receive International Morse Code. The

computer based Morse operator can use the PK-900 to send "perfect"

code at much higher speeds than are typical of hand sent code.

As a rule, no machine can receive Morse as well as the FSK modes.

Your PK-900 is no exception. A strong signal and a good "fist"

are both required for the PK-900 to do a reasonable job of copying

Morse code. Don't expect your PK-900 to do miracles and produce

good copy from bad fists!

8.2 Where to Operate Morse

Before you can operate Morse, you must first know where the activity

ocurrs. Morse operation is permitted on any amateur frequency, but

most often occurs in the lower 100 to 250 kHz of each band.

8.2.1 Entering the Morse Mode

If you are using an AEA PAKRATT program, follow the instructions in

the program manual to enter the Morse mode.

If you are using a terminal, simply type "MORSE" or "MO" from the

Command Mode followed by the <Enter> key to enter the Morse mode on

Radio Port 1. Packet operation on port 2 is disabled when in the

Morse mode. The PK-900 responds by displaying the previous mode:

Opmode was PAcket

Opmode now MOrse

8.2.2 HF Receiver Settings

Set your HF receiver (or transceiver) to the CW mode. Adjust the

volume to a comfortable listening level. Be certain that any IF-Shift

and Passband Tuning controls are centered or set to the OFF position.

8.2.3 Tuning in Morse Stations

Tuning in Morse stations properly is critical to successful operation.

Follow the procedure below for the best results in tuning in Morse

stations.

o Make certain your HF receiver is in the CW mode.

o Turn any IF-Shift and Passband-Tuning controls to the Center or

OFF position.

o Tune your receiver carefully in the lower portion of your

favorite amateur band and look for Morse signals.

1/93 8-1

Содержание PK-900









































































































































































































































































































































































































Результаты поиска

Содержание PK-900

Отзывы:

Похожие инструкции для PK-900

Бренды по названию

Популярные бренды

Timewave PK-900, Руководство по эксплуатации

Результаты поиска

Содержание PK-900

Отзывы:

Похожие инструкции для PK-900

Бренды по названию

Популярные бренды