Timewave PK-900 Скачать руководство пользователя страница 294

Страница: 294 / 392

COMMAND MNEMONIC FUNCTION

PACTime AFTER 10 Sets the packet automatic transmit timer

PACTor Immediate Command Enters the PACTOR mode (PT for short)

PARity 3 (even) Sets the terminal program parity (0-3)

PASs $16 <CTRL-V> Sets the converse mode pass character

PASSAll OFF/OFF Ignores CRC in receiving packets (Junk mode)

PErsist 63/63 Sets the P-persistent CSMA threshold

PPersist ON/ON Selects P-persistent CSMA operation

PRType 2 (Epson) Sets the graphics emulation for FAX printing

PT Immediate Command Enters the PACTOR mode (same as PACTOR)

PT200 ON Allows 200 bauds for PACTOR if link is good

PTConn Immediate Command Starts a PACTOR connect with (CALLSIGN)

PTHuff 0 Selects PACTOR data compression (0=OFF)

PTList Immediate Command Starts the PACTOR Listen mode

PTOver $1A <CTRL-Z> Sets the PACTOR link direction change char.

PTSend Immediate Command Starts the PACTOR unproto send mode (call CQ)

QHpacket 10/2 Sets the default HF packet modems

QMorse 12 Sets the default Morse modem

QRtty 1 Sets the default ASCII/Baudot RTTY modem

QSignal 2 Sets the default Signal Identification modem

QTDm 3 Sets the default TDM receive modem

QTor 2 Sets the default AMTOR modem

QVpacket 11/4 Sets the default VHF packet modems

QWide 7 Sets the default WIDESHFT ON modem

RAdio 1/2 Enables / Disables each radio port

RAWhdlc OFF Enables Raw HDLC for Host mode

RBaud 45 bauds (60 WPM) Sets the Baudot RTTY baud rate selection

Rcve Immediate Command Selects the receive mode Morse/RTTY/AMTOR

RECeive $04 <CTRL-D> Selects the receive character used in text

REDispla $12 <CTRL-R> Re-displays current terminal input buffer

RELink OFF/OFF Re-connects after link fails due to retries

RESET Immediate Command RESETs PK-900 and bbRAM to factory defaults

RESptime 0/0 Sets the minimum delay before sending an ACK

RESTART Immediate Command Restarts PK-900, same as turning power off/on

REtry 10/10 Sets the maximum number of packet repeats

RFec ON Receives FEC in AMTOR Standby

RFRame OFF Checks RTTY characters for framing errors

RXRev OFF Reverses the received data mark-space sense

SAmple Immediate Command Enters the raw data sampling mode

SELfec Immediate Command Starts a selective FEC call with SELCAL

SEndpac $0D <CTRL-M> Sets the converse mode "Send packet" char.

SIgnal Immediate Command Starts the Signal Identification mode

SLottime 30/30 (300 msec.) Sets the P-persistent CSMA slot time

SPACE 2200 Hz Sets or displays the current Space frequency

SQuelch OFF/OFF Sets the receiver squelch carrier polarity

SRXall OFF Allows reception of ALL received SELFEC calls

STArt $11 <CTRL-Q> Sets character to start sending terminal data

STOp $13 <CTRL-S> Sets character to stop sending terminal data

TBaud 1200 bauds Sets the ASCII terminal data rate

TClear Immediate Command Clears the transmit Buffer (Non-packet modes)

TDBaud 96 Sets the receive data rate for TDM signals

TDChan 0 Sets the receive channel for TDM signals

TDm Immediate Command Enters the TDM receive mode

TEST Immediate Command Starts the PK-900 self test function

3/93 4

Содержание PK-900









































































































































































































































































































































































































Результаты поиска

Содержание PK-900

Отзывы:

Похожие инструкции для PK-900

Бренды по названию

Популярные бренды

Timewave PK-900, Руководство по эксплуатации

Результаты поиска

Содержание PK-900

Отзывы:

Похожие инструкции для PK-900

Бренды по названию

Популярные бренды