manualshive.com logo in svg

Timewave PK-900, Руководство по эксплуатации, Страница: 269 / 392

Поделиться
Скачать
Timewave PK-900 Скачать руководство пользователя страница 269

________________________________________________________________________________ 

     SAmple "n"                                             Immediate Command 

     Mode: Command                                          Host: SA 

_________________________________ Parameters: __________________________________ 

 

"n"  -    20 to 255 specifies the sampling rate in baud. 

________________________________________________________________________________ 

 

This operating mode is for advanced users interested in decoding unknown  

synchronous data transmissions.  SAMPLE is similar to the 5BIT and 6BIT modes,  

but operates on synchronous data, whereas 5BIT and 6BIT are used on signals  

known to be asynchronous. 

 

SAMPLE synchronizes up on any regularly-paced data transmission received on  

Radio  

Port 1 and samples the data once per bit, packaging the data in groups and  

sending the groups to the user for further analysis.  The user can use SAMPLE to  

capture data bits from a synchronous transmission, such as FEC, TDM or an  

"unknown mode" not identified by the SIGNAL command.  The transmission is  

actually sampled several times per data bit.  The PK-900 does a majority vote  

on the last few samples to represent the value of the data bit. 

 

One use for the SAMPLE command is to record the output to a disk file, then  

write a program to analyze the results for synchronous/asynchronous, bit sync  

patterns, data decoding, etc. 

 

SAMPLE data is captured in 6-bit units; the order of bit reception is MSB first,  

LSB last.  The TNC sends the data unit to the user with a constant of hex 30  

added to each unit, the same as the 6BIT command.  The 6-bit unit is a  

compromise between hexadecimal and 8-bit binary output.  The 6-bit unit yields  

shorter disk files than 4-bit hexadecimal characters, but encounters no  

interference from terminal communications programs and the TNC's Converse and  

Command modes.  The 6-bit unit's range of $30-6F falls within the printable  

ASCII range, allowing the TNC to insert end-of-line carriage returns that can be  

ignored by the user's analysis software. 

 

To use SAMPLE, set ACRDISP to a non-zero value such as 77.  This will break up  

the recorded disk file into lines.  Tune in the signal, set WIDESHFT ON or OFF  

as needed, and get the transmission rate from the SIGNAL command.  Now type  

"SAMPLE (rate)".  As an example, SIGNAL may identify a transmission as 96 baud  

TDM; in this case type the following: 

 

          SAMPLE 96 <Carriage Return> 

 

Now begin the capture to a disk file with the terminal program.  At the end of  

the session, edit the disk file and remove any TNC commands that were echoed  

before or after the received data. 

 

Occasionally SIGNAL will identify a Baudot transmission at a rate that SAMPLE  

cannot sync up on.  This would happen if the Baudot signal had a stop bit  

duration 1.5 times the data bit duration.  In this case, SAMPLE at twice the  

baud rate and compensate for the doubled data bits in the analysis software.   

Note that it might be more useful to let the TNC do the start/stop bit work by  

using the 5BIT command rather than SAMPLE.  5BIT uses RBAUD, and adds a constant  

of hex 40 to each 5-bit character received. 

 

Note:     RXREV does affect the sense of the SAMPLE data. 

          RXREV should however not be changed while capturing data. 

 

1/93                                   A-91 

Содержание PK-900









































































































































































































































































































































































































Отзывы:

Нет отзывов