Timewave PK-900 Скачать руководство пользователя страница 55

Страница: 55 / 392

After pressing <Enter>, you should observe the TX LCD light.

Your monitor should soon display:

*** CONNECTED to (Callsign)

If you see this, you have just Connected to your first packet station.

Identify what type of station you have connected to, and respond

appropriately. After you have connected to a few stations, you should

skip to section 4.4 to learn more about the PK-900 packet features.

4.3.6 I'm Having Trouble Connecting

If the station you are trying to connect to is connected to someone

else, you may see the following message:

*** BUSY from (Callsign) DISCONNECTED

If you see this, simply wait a few minutes and try again or try

connecting to a different station from your MHEARD list.

If the distant station cannot hear you, you may see the following:

*** Retry count exceeded

*** DISCONNECTED:

A number of different things can cause this to occur. It may simply

be that the station you are trying to connect to is out of your

transmitter's range. It is possible however that something more

serious is wrong, so you should check the following before proceeding:

o The Loopback Test in section 4.2 functions properly.

o Your PK-900's AFSK Output Level control, radio microphone gain,

and deviation are set properly as discussed in Section 3.5.1.

o All cables and connectors are properly installed.

o Your radio's volume and squelch are set for local conditions.

o You are following the correct procedure for Connecting.

Remember that this procedure is slightly different for AEA

PAKRATT programs than it is for terminals or terminal-programs.

o The "VHF" command is "ON" for VHF/UHF operation.

o HB is set to 1200

o RESET the PK-900 with the RESET command or RESET switch and

start over with section 4.2 of this chapter.

If none of the above correct the problem, ask one of your area's

experienced packet operators to listen to your transmissions. Both

you and your partner should set MONITOR and MCON to 6, and then send

some packets. Each station should display packets sent by the other.

o If only one station is "hearing" packets, check the modulator and

transmitter of that station and the demodulator and receiver of

the other station.

o Experiment with the TXDELAY parameter for the sending TNC. Try

setting TXDELAY 64 for a long delay. If this solves the problem,

decrease TXDELAY to the smallest value that works all the time.

If you still cannot connect to other stations, then you should contact

AEA Technical Support as outlined in the PREFACE of this manual.

1/93 4-13

Содержание PK-900









































































































































































































































































































































































































Результаты поиска

Содержание PK-900

Отзывы:

Timewave PK-900, Руководство по эксплуатации, Страница: 55 / 392

Результаты поиска

Содержание PK-900

Отзывы: