manualshive.com logo in svg

Timewave PK-900, Руководство по эксплуатации


Поделиться
Скачать
background image

9

Installation 

without

 a DSP Daughterboard

1)  Locate and remove U36, U37 and U44 (See Figure A.)

2) Use an IC removal tool if you have one. If not, slide the flat blade of the screwdriver under one end

of the chip and elevate carefully. Do the same thing at the other end of the IC and it will pop out
cleanly. BE SURE the screwdriver is between the IC and the chip socket, NOT between the chip
socket and the board.

3) Install the new 32 pin eprom in U36. Be very careful to orient the notch in the end of the chip to

match the notch in the outline on the circuit board. Make sure all pins are straight and fit direcltly
into the Eprom socket before you carefully press the new eprom into the socket. All pins should be
inserted directly into the socket with no pins curled under the chip or bent outside the socket.

4) Install the new PAL C  in U44. Be very careful to orient the notch in the end of the chip to match the

notch in the outline on the circuit board. Make sure all pins are straight and fit direcltly into the
Eprom socket before you carefully press the new eprom into the socket. All pins should be inserted
directly into the socket with no pins curled under the chip or bent outside the socket.

5) Locate and remove C40 near J1 (see Figure B).

We recommend that you remove the capacitors and resistors by desoldering them from the back of
the board. Remove the solder from the holes with a solder sucker tool or solder wick.  Use care not
to overheat the board. You may burn the board or damage the pad or barrel in the hole.  When hole
and the lead are clear of solder, gently remove the component from the top of the board. In some
cases, it may be easier to remove the component by clipping the leads of the component close to the
body of the component before desoldering it..  Then while holding the lead with the needle nose
pliers, CAREFULLY heat the solder just until the lead can be removed without force.  Be very
careful not to pull the barrel from the board by pulling before the solder flows. DO NOT OVER-
HEAT.  The hole can then be cleaned with a solder sucker tool or solder wick.

     You will also need to clean the solder from the C40 pads. Observe the same precautions as above and

do not overheat the board.

6) Locate and remove C89  (see Figure B).

You will also need to clean the solder from the C89 pads. Observe the same precautions as above
and do not overheat the board.

7)  Remove R253, if it is installed on your PK-900. See Figure A.

You will also need to clean the solder from the R253 pads. Observe the same precautions as above
and do not overheat the board.

8)  Re-install the main board on the chassis using the screws you saved when you removed it.

9)  Reconnect the front panel connectors to the main board.

Содержание PK-900









































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для PK-900

Cansec H1000 Installation Manual And Instructions For Use preview
H1000
Бренд: Cansec Страницы: 45
Cansec CP40 Installation Manual preview
CP40
Бренд: Cansec Страницы: 43
Cansec MAP2 Installation Manual preview
MAP2
Бренд: Cansec Страницы: 32
IFM Electronic ecomat 100 R 360 Operating Instructions Manual preview
ecomat 100 R 360
Бренд: IFM Electronic Страницы: 16
IFM Electronic Ecomot300 AC2630 Operating Instructions Manual preview
Ecomot300 AC2630
Бренд: IFM Electronic Страницы: 11
IFM Electronic AC1331 Installation Instructions Manual preview
AC1331
Бренд: IFM Electronic Страницы: 23
JENCO 6311 Operation Manual preview
6311
Бренд: JENCO Страницы: 36
jcm-tech WAVE500 User Manual preview
WAVE500
Бренд: jcm-tech Страницы: 8
Kamstrup M-Bus Manual preview
M-Bus
Бренд: Kamstrup Страницы: 36
JFA Electronicos K1200 Instruction Manual preview
K1200
Бренд: JFA Electronicos Страницы: 29
u-blox M8 Series Hardware Integration Manual preview
M8 Series
Бренд: u-blox Страницы: 28
u-blox EVK-NINA-W151 Quick Start preview
EVK-NINA-W151
Бренд: u-blox Страницы: 2
Jetter 60873050 Manual preview
60873050
Бренд: Jetter Страницы: 24
Centurion TB-CN2R1 Instruction Manual preview
TB-CN2R1
Бренд: Centurion Страницы: 16
Zapf Creation Baby Born 828656 Manual preview
Baby Born 828656
Бренд: Zapf Creation Страницы: 2
Mazurczak MTR 3000 Installation And Operating Instructions Manual preview
MTR 3000
Бренд: Mazurczak Страницы: 9
SOMFY Situo 1 RTS Installation And Operating Manual preview
Situo 1 RTS
Бренд: SOMFY Страницы: 112
asalvo TRIO ROMA Instruction Manual For Use preview
TRIO ROMA
Бренд: asalvo Страницы: 46

Бренды по названию

Популярные бренды

Загрузить еще бренды