Timewave PK-900 Скачать руководство пользователя страница 27

Страница: 27 / 392

Enter <CONTROL-C>

Your monitor should respond with the command prompt:

cmd:

Enter D <Enter>

Your monitor should respond with:

cmd:*** DISCONNECTED: AAA

p1 AAA*>AAA (UA)

If all of the above steps were successful, you've completed the quick-

check and are ready to proceed to Chapter 3. In Chapter 3 you will

connect your PK-900 to your radio and begin using it "on the air".

If you have problems with the steps shown above, go back to Step 1

AFTER checking all cables and connectors. Read each step again

carefully. The most common problems are trying to connect to a call

different from AAA, not having the "loopback" jumpers in the

correct pins, or not setting the AFSK levels to 50% rotation.

If you still have problems, leave your PK-900 ON and contact AEA's

Technical Support Department as suggested in the front of this manual.

2.6 Detailed RS-232 Connections for Other Computers

If the type of computer you plan to use with the PK-900 was not

mentioned in the beginning of this chapter, you may find specific

connection information in the sections below. You will also need a

Communications program to use with your computer which AEA can not

provide. See section 2.7 for information regarding Communication

programs for many of these machines.

Some computers require a serial port adapter card that incorporates

the necessary RS-232-C interface circuitry. The IBM-PC and Apple II

series of computers are good examples of this.

Computers that do not have a serial port or do not permit use of a

suitable adapter or level converter cannot be used with the PK-900.

2.6.1 Apple II Series

The Apple II, II+ and IIe computers require an RS-232 Serial card to

connect to your PK-900. The most popular we know about is the

Super-Serial Card which should be available from your Apple dealer.

2.6.2 Commodore C-64, C-128 and Vic 20

Commodore, OMNITRONIX and other manufacturers sell a signal level

converter that is installed in the User Port Connector on the rear of

the computer. The converter changes the computer's internal TTL

voltage levels to the proper RS-232-C voltage levels and polarities.

2.6.3 IBM PCjr

The PCjr uses standard RS-232-C voltage levels; however, the

1/93 2-9

Содержание PK-900









































































































































































































































































































































































































Результаты поиска

Содержание PK-900

Отзывы:

Timewave PK-900, Руководство по эксплуатации, Страница: 27 / 392

Результаты поиска

Содержание PK-900

Отзывы: