Timewave PK-900 Скачать руководство пользователя страница 281

Страница: 281 / 392

UBIT 18: OFF: In Packet operation, the FRACK (or FRICK if enabled) timer is

used to retry packets that were not acknowledged.

ON: An experimental Master/Slave relationship is established when a

Packet connection is made. This is designed for meteor scatter

operation and is described in detail under the FRICK command.

UBIT 19: ON: The "p1" and "p2" radio port designators are shown ahead of

monitored data on each radio port.

OFF: The "p1" and "p2" radio port designators are not displayed.

UBIT 20: OFF: In the Analog receive mode, each 8 bit sample is sent to the

computer as an 8 bit byte of data.

ON: In the Analog receive mode, each 8 bit sample is truncated to

the 4 Most Significant bits. Two 4 bit samples are then packed

together to form an 8 bit byte before being sent to the computer.

UBIT 21: Not used in the PK-900.

UBIT 22: ON: In the Packet mode, the PK-900 will respond to the receipt of

an UNPROTO frame addressed to QRA by sending an UNPROTO ID

packet frame within 1 to 10 seconds. This feature is compatible

with TAPR's ANSWRQRA command.

OFF: The PK-900 does not respond to UNPROTO frames addressed to QRA.

UBIT 23 ON: The TEST function halts at the end of each test measurement.

Pressing any key except "Q" starts the next test. Pressing "Q"

halts the test and returns to command mode.

OFF: The TEST function will halt for the discriminator adjustment

functions only. The rest of the test will continue until

complete or may be stopped by pressing the "Q" key.

UBIT settings 24 and above are unused at the present time but are reserved for

future expansion.

1/93 A-103

Содержание PK-900









































































































































































































































































































































































































Результаты поиска

Содержание PK-900

Отзывы:

Похожие инструкции для PK-900

Бренды по названию

Популярные бренды

Timewave PK-900, Руководство по эксплуатации

Результаты поиска

Содержание PK-900

Отзывы:

Похожие инструкции для PK-900

Бренды по названию

Популярные бренды