Timewave PK-900 Скачать руководство пользователя страница 3

Страница: 3 / 392

Welcome

Congratulations!! You've purchased another fine

Timewave

product.

PLEASE, before we go any further, may we ask you to FILL OUT AND RETURN the

Warranty Registration Card, which has been packed with your PK-900.

Product Update Policy

From time to time

Timewave

may make available updates to the design of its

products. We can only tell you about these updates if we have your warranty

card on file. PLEASE SEND IT IN if you have not already done so.

In Case of Trouble

Application and troubleshooting assistance may be obtained by calling

Timewave

during

our 8:00

- 5:00

working hours in

St. Paul, MN

. Ask for the Technical

Support Department. The phone number is (

651

)

489

5080

. Please have your

PK-900's serial number and version date of the software available. The

version date is on the first screen that comes up when you turn on the PK-900.

We will also need to know the nature of any other equipment connected to the

PK-900.

You may wish to attempt to solve problems locally, using other hams or an

Timewave

dealer. A helpful Amateur with equipment similar to your own may literally be

just around the corner. Substituting another PK-900 or Data Controller that

you know is working properly for your questionable one is a diagnostic

technique that will check out the rest of your station. You may also try

running your PK-900 in another station if possible.

Timewave

provides

Technical Support for its line of amateur radio equipment

Email addres

es are:

[email protected] and [email protected]

If you call for assistance, please have your PK-900 up and running beside the

phone. Our Support technician will likely ask you to perform certain keyboard

routines to aid in diagnosis. If you have a voltmeter handy, you might have

the PK-900 open so you can report measurements to the technician.

Many of the

Timewave

products that are sent to us for repair are in perfectly good

order when we receive them. There is a test and alignment charge for units

returned to us in working order. Please perform whatever steps are applicable

from the installation sections of this manual to insure that there is a problem.

PLEASE DO NOT RETURN THE PK-900 TO US WITHOUT CONTACTING US FOR PERMISSION AND

AN RMA NUMBER. WE WOULD LIKE THE OPPORTUNITY TO TROUBLESHOOT THE PROBLEM OVER

THE PHONE FIRST, SAVING YOU BOTH TIME AND MONEY.

If the unit must be sent in, we will give you a Return to Manufacturer

Authorization (RMA) number over the telephone. This number allows us to track

your unit and provide you with its status. Please write this number on the

outside of the box so we may process your unit as quickly as possible.

1/93 ii

Содержание PK-900









































































































































































































































































































































































































Результаты поиска

Содержание PK-900

Отзывы:

Похожие инструкции для PK-900

Бренды по названию

Популярные бренды

Timewave PK-900, Руководство по эксплуатации

Результаты поиска

Содержание PK-900

Отзывы:

Похожие инструкции для PK-900

Бренды по названию

Популярные бренды