Timewave PK-900 Скачать руководство пользователя страница 252

Страница: 252 / 392

________________________________________________________________________________

MYGate call[-"n"] Default: none

Mode: Packet Host: MY

_________________________________ Parameters: __________________________________

call - The Call Sign you wish to use for the Gateway.

"n" - Numeral indicating an optional substation ID (SSID) or extension.

________________________________________________________________________________

Call is the call sign of the Gateway, default "none."

"Call" may have an optional SSID, and must not be the same call sign and SSID as

MYCALL or MYMAIL. When another station digipeats via the callsign set in

MYGATE, your PK-900 will provide Gateway operation between Radio Port 1 and

Radio Port 2 provided both ports are enabled for Packet operation.

See Chapter 4 for details of Gateway operation and limitations.

________________________________________________________________________________

MYMail call[-"n"] Default: none

Mode: Packet, PACTOR/MailDrop Host: Ma

_________________________________ Parameters: __________________________________

call - The Call Sign you wish to use for the MailDrop.

"n" - Numeral indicating an optional substation ID (SSID) or extension.

________________________________________________________________________________

Call is the call sign of the MailDrop, default "none."

"Call" may have an optional SSID, and must not be the same call sign and SSID as

MYCALL. If you do not set MYMAIL, the MailDrop will use the same call sign and

SSID as entered in MYCALL. For example, if you have set MYCALL to N7ML then

MYMAIL may be N7ML-1 through N7ML-15. You can use the CTEXT and MTEXT messages

to inform other stations who connect of your MYCALL and MYMAIL call signs.

_________________________________________________________________________________

MYPTcall call Default: PK900

Mode: PACTOR Host: Mf

________________________________________________________________________________

Use the MYPTCALL comand to load your call sign into your PK-900. Only radio

port 1 will operate on PACTOR.

If you have not loaded a call into the PK-900 with MYPTCALL the call loaded

in MYCALL will be used. The difference between MYCALL and MYPTCALL is that

MYCALL allows only the dash (-) to be used while MYPTCALL will allow any

punctuation with the call.

If calls have not been loaded into either MYCALL or MYPTCALL, the PK-900 will

not allow transmission on PACTOR. An error message "Need MYCALL" will be

displayed if transmission is attempted.

3/93 A-74

Содержание PK-900









































































































































































































































































































































































































Результаты поиска

Содержание PK-900

Отзывы:

Timewave PK-900, Руководство по эксплуатации, Страница: 252 / 392

Результаты поиска

Содержание PK-900

Отзывы: