manualshive.com logo in svg

Timewave PK-900, Руководство по эксплуатации, Страница: 382 / 392

Поделиться
Скачать
Timewave PK-900 Скачать руководство пользователя страница 382

10

Installation 

without

 a DSP Daughterboard

Connections

Follow the next steps to connect the wires from the back panel as shown in Figure A and B.

1) Connect PSK enable J5 on PSK board (grey wire) to PB0 (hole from lead of  R253 closest to left side

of PK-900).

2) Connect J1 (+12V) (red wire) to D21 (1N4004 smaller diode on the left closest to the heatsink) anode

lead on PK-900 main board. The anode lead is toward the front of the PK-900 and is the end of the
diode without the light-colored band on the body of the diode. Wrap the stripped wire lead from J1
around the lead of the diode as far as possible from the body of the diode. Solder the two leads
together.

3) Connect J6 (GND) (black wire) to to the solder lug on the top of the DC power jack on PK-900 main

board.

4). Connect J2 (RX Audio in) (violet wire) to C89 Rear Pad  on PK-900 main board.

5) Connect J3 (RX audio out) (white wire) to the C89 Front pad on the PK-900 main board.

6). Connect J7 (TX audio in) (brown wire) to the C40 left pad on PK-900 Main board.

7). Connect J4 (TX Audio out) (orange wire) to the C40 right pad on PK-900 main board.

8) If you have one, re-install the 9600 baud board. Be very careful not to bend the 20 pins on the bottom

of the board.  Fasten the board with the four screws removed when the board was temporaily re-
moved. All the leads from the PSK board should be under the 9600 baud board. Do not pinch any
wires under the board standoffs or sockets.

9) Fasten the new back panel assembly to the bottom cover of the PK-900 with 3 screws removed with

the old back panel, the two knurled nuts on the RX AUDIO IN jacks, and the two jack screws on the
RS-232 Serial Connector.

10) Secure the chassis top with all 4 screws.

11) Place the enclosed sticker (PSK) below the raised “AEA” logo on the left side of the front
        panel of the PK-900.  Place it one inch above  the bottom edge of the panel.

12) Reconnect the unit and reset when powering on for the first time.

Содержание PK-900









































































































































































































































































































































































































Отзывы:

Нет отзывов