Timewave PK-900 Скачать руководство пользователя страница 179

Страница: 179 / 392

APPENDIX A

COMMAND SUMMARY

A.1 Introduction

Your PK-900 is controlled by Commands that you enter from the

keyboard. Most of these commands have a standard (default) value

that provides good performance. There are however a few commands

that you will need to change. This section is intended as a command

and error message reference and is not meant to be read from start

to finish.

A.1.1 Entering Commands

AEA Software for the PK-900 such as PC-PAKRATT II and MACRATT have

menus and even on-line help for commands. If you are using an AEA

program, please consult the program manual for instructions on

entering commands. The instructions below assume you are using a

terminal or terminal-emulating program on your personal computer.

Commands are short names for the instruction you want the PK-900 to

perform. Commands are entered after the Command prompt "cmd:".

o You may use either UPPER or lower case when entering commands.

o End the command with a carriage return <CR> or the <Enter> key.

o Correct any typing mistakes before typing the final <Enter>.

A.1.2 Command Responses

Whenever the PK-900 accepts a command it responds by displaying both

the old and new values. For example, if you type "XFLOW OFF" - you'll

see the display:

XFlow was ON

XFlow now OFF

This message tells you that the value has been changed successfully.

A.2 Command List

Commands are listed alphabetically in the following command

descriptions. Each command entry contains several sections:

Command Name, Default Value, Mode(s) in which the command is used,

HOST mode abbreviation (for HOST mode programmers), and Parameters

A.2.1 Command Names and Abbreviations

The command name at the beginning of the description is the full word

you can type in order to have your PK-900 execute this command. The

capital letters indicate the minimum abbreviation you can use instead

of the full word. For example:

You can enter the command MYCALL by simply typing "MY". (Note: DO NOT

type the "quotation marks") The abbreviation "M" is not sufficient,

but "MY", "MYC", "MYCA", "MYCAL" or "MYCALL" are all acceptable.

3/93 A-1

Содержание PK-900









































































































































































































































































































































































































Результаты поиска

Содержание PK-900

Отзывы:

Timewave PK-900, Руководство по эксплуатации, Страница: 179 / 392

Результаты поиска

Содержание PK-900

Отзывы: