Timewave PK-900 Скачать руководство пользователя страница 284

Страница: 284 / 392

________________________________________________________________________________

USOs ON|OFF Default: OFF

Mode: Baudot RTTY Host: US

_________________________________ Parameters: __________________________________

ON - Letters (LTRS) case IS forced after receiving a space character.

OFF - Letters (LTRS) is NOT forced after receiving a space character.

________________________________________________________________________________

Use the USOS Command (UnShift On Space) when you want your PK-900 to

automatically change from figures to letters after receiving a space character.

When using Baudot RTTY in poor HF receiving conditions, a received character can

be incorrectly interpreted as a FIGURES-SHIFT character, forcing the received

data into the wrong case. Many otherwise good characters received after this

will be interpreted as figures (numbers and punctuation), not as the letters

sent by the distant station. USOS ON helps reduce these receiving errors.

________________________________________________________________________________

Vhf ON|OFF/ON|OFF Default: ON/ON

Mode: Packet Host: VH

_________________________________ Parameters: __________________________________

ON - The modem selected in QVPacket is automatically selected.

OFF - The modem selected in QHPacket is automatically selected.

________________________________________________________________________________

Use the VHF Command for immediate software control of the PK-900's modem

selection. This command makes changing between HF and VHF packet modems on

each radio port easier. Remember to change HB appropriately.

Set VHF ON for VHF packet operation (default) and set VHF OFF for HF operation.

________________________________________________________________________________

VOltage Immediate Command

Mode: Command Host: VO

________________________________________________________________________________

The VOLTAGE command displays the result of three internal voltage measure-

ments. These measurements are:

1. The internal analog reference voltage. Nominally 6.70 volts, it

may range from 6.25 to 6.95 volts.

2. The 12 volt input. Two numbers will be displayed which are the

minimum and maximum values of the input voltage. For a well

regulated power supply, these numbers will be very nearly the same.

For a wall mount transformer, the numbers will typically have a two

volt difference. The lowest value should not be below 11.5 volts.

3. The internal 5 volt power supply. The range of values should be

between 4.6 and 5.4 volts.

1/93 A-106

Содержание PK-900









































































































































































































































































































































































































Результаты поиска

Содержание PK-900

Отзывы:

Похожие инструкции для PK-900

Бренды по названию

Популярные бренды

Timewave PK-900, Руководство по эксплуатации

Результаты поиска

Содержание PK-900

Отзывы:

Похожие инструкции для PK-900

Бренды по названию

Популярные бренды