Timewave PK-900 Скачать руководство пользователя страница 239

Страница: 239 / 392

_______________________________________________________________________________

MARK "n" Default: Current modem mark frequency

Mode: Command Host: Mk

_________________________________Parameters_____________________________________

"n" - 500 to 3000 specifies the transmit mark frequency in Hz.

_______________________________________________________________________________

The MARK command is used to select a non-standard mark tone transmit frequency.

The mark tone frequency range is 500 to 3000 Hz. If the MARK command is

entered without an argument ("n"), the current mark frequency is displayed.

_______________________________________________________________________________

MARsdisp ON|OFF Default: OFF

Mode: Baudot and AMTOR, RTTY Host: MW

_________________________________ Parameters: __________________________________

ON - The PK-900 translates received LTRS characters to a <CTRL-O>, and

FIGS characters to a <CTRL-N> and sends these to the terminal.

OFF - The PK-900 operates as before in Baudot and AMTOR (default).

________________________________________________________________________________

The MARSDISP command permits the Baudot and AMTOR operator to detect and display

every character including LTRS and FIGS sent by the other station. The ACRDISP

and ALFDISP may be turned off to prevent extraneous carriage-returns and

Linefeeds from being sent to the display. If this data is retransmitted,

ACRRTTY should be 0, and ALFRTTY should be OFF. The <CTRL-O> and <CTRL-N>

characters will send LTRS and FIGS respectively.

________________________________________________________________________________

MAXframe "n/n" Default: 4/4

Mode: Packet Host: MX

_________________________________ Parameters: __________________________________

"n" - 1 to 7 signifies a number of packet frames.

________________________________________________________________________________

MAXFRAME limits the number of unacknowledged packets your PK-900 permits on

the radio link for each Radio Port. It is also the number of contiguous packets

your PK-900 will send in a single transmission.

The "best" value of MAXFRAME depends on your local channel conditions. In most

cases of local VHF packet keyboard operation, the default value of MAXFRAME 4

works well. When the amount of traffic is heavy, the path in use is poor as on

HF, you are using many digipeaters, you can actually improve your throughput by

reducing MAXFRAME. When operating HF packet try setting MAXFRAME to 1.

1/93 A-61

Содержание PK-900









































































































































































































































































































































































































Результаты поиска

Содержание PK-900

Отзывы:

Похожие инструкции для PK-900

Бренды по названию

Популярные бренды

Timewave PK-900, Руководство по эксплуатации

Результаты поиска

Содержание PK-900

Отзывы:

Похожие инструкции для PK-900

Бренды по названию

Популярные бренды