manualshive.com logo in svg

Timewave PK-900, Руководство по эксплуатации, Страница: 71 / 392

Поделиться
Скачать
Timewave PK-900 Скачать руководство пользователя страница 71

 

               If the tuning indicator looks like the one below, the audio  

               frequency from your speaker is too high for the PK-900 to copy  

               packets.  Slowly tune the VFO and make the frequency lower. 

 

            

——————————————————————————————————————————————————————————————

 

       MARK |  

 

 

 

 

 

   

  

 

  

          

  

      | SPACE 

            

——————————————————————————————————————————————————————————————

 

                  Tuning too high for discriminator indicator (BAR 0)   

 

 

            

——————————————————————————————————————————————————————————————

 

            |  

 

 

 

 

    

           

 

  

          

  

      | 

            

——————————————————————————————————————————————————————————————

 

                    Tuning too high for magic eye indicator (BAR 3) 

 

 

            

——————————————————————————————————————————————————————————————

 

            |  

 

 

 

 

 

 

  

  

 

  

 

 

 | 

            

——————————————————————————————————————————————————————————————

 

                   Tuning too high for center tune indicator (BAR 2) 

 

 

          o    Adjust the volume on the receiver so that the DCD LCD lights  

               when a properly tuned packet is being received. 

               You must also make certain that the DCD LCD goes out when no  

               packet signals are present on the frequency. 

 

               After you have a packet station tuned in, you should start seeing  

               HF packet stations on your display. 

 

4.7.5     Transmitter Adjustments 

 

          Make sure your PK-900 is adjusted for your SSB transmitter as  

          described in section 3.5 and 3.5.2 of this manual before transmitting.   

          These are very critical adjustments.  If the AFSK level and  

          transmitter microphone gain are not adjusted properly, other stations  

          will not be able to copy your packets.  Check your plate or collector  

          current or the power output of your rig before going on the air. 

 

 

4.7.6     Going On The Air 

 

          Make sure your transmitter and antenna are tuned and adjusted for the  

          band and operating frequency you are using. 

 

          On HF there are two ways you can go about talking to another station.   

 

          o    First, you can look at the packets you have just MONITORED  

               (or in your MHEARD list) and choose one of them to connect to. 

 

          o    You can also "Call CQ" by entering the CONVERSE mode and pressing  

               the <Enter> key a few times. 

 

          Either way you decide to go on the air, remember that things happen  

          much more slowly on HF packet than they do on VHF packet.  HF packet  

          requires patience and careful tuning in order to be used successfully. 

 

 

3/93                                    4-29 

Содержание PK-900









































































































































































































































































































































































































Отзывы:

Нет отзывов