Timewave PK-900 Скачать руководство пользователя страница 44

Страница: 44 / 392

4.2 Packet Introduction

You've now connected your PK-900's transmit audio output to its

receive audio input. Your PK-900 can now "talk to itself" in

packet.

1. Set the rear-panel AFSK level control for RADIO-1 at 50%

(straight up and down) for the following Packet introduction.

NOTE: If you have adjusted the RADIO-1 rear-panel AFSK level

control for a particular transceiver in chapter 3, then mark

this setting with a pencil so it can be reset when finished.

2. Turn on your computer. Load and run your communications program.

If you are using an AEA PAKRATT Program, follow the program

manual's instructions to enter the Packet mode on Radio Port 1,

and then skip to step 4.

If you are using another Computer program or a Terminal, set the

communication parameters as done in Chapters 2 and 3.

3. Press the PK-900's front panel power switch to the ON position

if you have not already done so.

You should notice the sign-on message seen in chapter 2. The LCD

Status display should indicate you are in the Packet mode.

4. After you have seen the sign-on message and/or entered the Packet

mode, you must enter your own callsign (with the MYCALL Command)

if you are to converse with any other Packet stations. If you

try to connect to a station without entering your call sign, your

PK-900 will send you the following message:

?need MYcall

If you are an SWL and do not intend to transmit, you should enter

"AAA" as a Callsign (MYCALL).

If you are using an AEA PAKRATT program, follow the instructions

in the Program Manual to enter your callsign. If you are using a

terminal or terminal emulating program on your computer, you must

use the MYCALL command to install your call sign.

Note that since the PK-900 has two radio ports, you must enter

a callsign for each port. The callsigns may be the same, or can

be different to make life a little easier in the "two Ham"

family. You must change the callsign from the default "PK900"

on each radio port, or that port will not transmit packets. For

example, if your Callsign is WX2BBB, enter the following:

cmd:MYCALL WX2BBB/WX2BBB <Enter>

The PK-900 will respond with:

MYcall was PK900/PK900

MYcall now WX2BBB/WX2BBB

1/93 4-2

Содержание PK-900









































































































































































































































































































































































































Результаты поиска

Содержание PK-900

Отзывы:

Похожие инструкции для PK-900

Бренды по названию

Популярные бренды

Timewave PK-900, Руководство по эксплуатации

Результаты поиска

Содержание PK-900

Отзывы:

Похожие инструкции для PK-900

Бренды по названию

Популярные бренды