Timewave PK-900 Скачать руководство пользователя страница 236

Страница: 236 / 392

________________________________________________________________________________

KIss "n" Default: 0

Mode: Packet Host: KI

_________________________________ Parameters: __________________________________

"n" - Is a HEX number from $00 (KISS disabled) through $FF that enables the

KISS mode selected from the table below.

________________________________________________________________________________

The KISS mode must be entered to prepare the PK-900 for KISS operation.

TCP/IP and other special applications have been written that require the KISS

mode be enabled to operate correctly. For normal AX.25 Packet operation, this

command should be left at 0 or OFF (default). When KISS operation is enabled,

the PK-900 no longer operates in any other modes on either Radio Port.

The KISS command, takes a numerical argument from $00 - $FF.

The table below describes available KISS options.

KISS $00: KISS disabled (formerly displayed as KISS OFF)

KISS $01: Standard KISS (same as KISS ON or KISS YES)

KISS $03: Extended KISS

KISS $07: Extended KISS + KISS polling enabled

KISS $0B: Extended KISS + KISS checksum enabled

KISS $0F: Extended KISS + KISS polling and checksum enabled

Note that KISS ON enables standard KISS operation for compatibility with

existing applications.

Extended KISS mode adds these commands to the standard commands ($x0-$x5):

$xC signifies data to be transmitted. Unlike the $x0 command, the $xC byte is

followed by two frame ID bytes, then the data; when the TNC transmits the frame,

it notifies the host application by echoing back FEND, the $xC byte, the two

frame ID bytes, and FEND.

$xE is the polling command, similar to the HOST "GG" command existing in AEA

products. Polling makes multi-TNC KISS operation possible. If KISS polling is

enabled, the TNC holds received data until the host application sends the poll

command. If the TNC is holding no data, it echoes back FEND $xE FEND. The "x"

in "$xE" must match the number in the KISSADDR command for the TNC to respond.

If KISS checksum is enabled, a checksum byte is added to the end (before the

final FEND) of all KISS blocks flowing between the TNC and the host application.

The checksum is the exclusive-OR of all other bytes between the FEND bytes,

taken before KISS escape transpositions. A checksum is helpful when using

multiple TNCs on a marginal RS-232 link. If the PK-900 receives a KISS block

with a bad checksum, it does not transmit the data.

In KISS and Raw HDLC modes, the SYSTEM status HOST LCD will be on.

1/93 A-58

Содержание PK-900









































































































































































































































































































































































































Результаты поиска

Содержание PK-900

Отзывы:

Timewave PK-900, Руководство по эксплуатации, Страница: 236 / 392

Результаты поиска

Содержание PK-900

Отзывы: