Timewave PK-900 Скачать руководство пользователя страница 340

Страница: 340 / 392

PK-900 Gateway Option Supplement

AList

Immediate Command

Mode: AMTOR

Host: AL

In AMTOR Listen (and PACTOR Listen) modes, monitored link attempts are now

displayed like this:

>W1AW <C>

The callsigns are shown one per line and are meant to resemble the way the TNC

monitors packet connect frames. Since neither mode supports identification

within the calling blocks, no source callsign can be shown.

ARXTor ON|OFF

Default: OFF

Mode: AMTOR and PACTOR

Host: Ar

Parameters:

Enables automatic detection and switching between AMTOR and PACTOR

modes.

OFF

Disables the automatic detection of non-selected operating modes.

The ARXTOR command allows the automatic switching from PACTOR Listen mode to

AMTOR FEC receive, and from PACTOR Standby to AMTOR ARQ. It also allows the

automatic switching from AMTOR Listen to AMTOR FEC receive.

With ARXTOR ON, an AMTOR FEC signal is detected by ALIST and PTLIST modes as

well as AMTOR Standby mode. There are two methods of FEC mode recognition.

AMTOR Standby, ALIST and PTLIST all use FEC idles to recognize FEC transmis-

sions. However, in the AMTOR Standby mode, FEC text patterns are recognized as

an additional quick recognition method which may speed locking onto a FEC

signal.

ARXTOR ON enables PTLIST mode to monitor AMTOR ARQ transmissions.

ARXTOR ON also means an incoming AMTOR ARQ call is recognized in PACTOR

Standby mode. Only a call for the selcall in MYSELCAL is recognized; PACTOR

cannot detect ARQ calls to MYALTCAL or MYIDENT.

When a PACTOR mode detects an AMTOR transmission, there is an added delay

before the text is shown. Your TNC must switch from PACTOR to AMTOR, where the

signal is again detected. For fastest detection of AMTOR FEC, your TNC should

be in the AMTOR Standby mode. For fastest syncing on AMTOR ARQ signals, the

TNC should be in ALIST mode.

At the end of the new mode (AMTOR ARQ or FEC), your TNC returns to the origi-

nal monitoring mode (AMTOR, ALIST, PACTOR or PTLIST).

Содержание PK-900









































































































































































































































































































































































































Результаты поиска

Содержание PK-900

Отзывы:

Похожие инструкции для PK-900

Бренды по названию

Популярные бренды

Timewave PK-900, Руководство по эксплуатации

Результаты поиска

Содержание PK-900

Отзывы:

Похожие инструкции для PK-900

Бренды по названию

Популярные бренды