Timewave PK-900 Скачать руководство пользователя страница 29

Страница: 29 / 392

Computer PK-900 (DB25)

TXD .......................... 2

RXD .......................... 3

GND .......................... 7

o As a default the PK-900 provides XON/XOFF software flow-control

to the computer or terminal. The command XFLOW can be

turned OFF to enable hardware handshake if your computer

requires it.

Hardware flow control is achieved with RTS/CTS (pins 4 and 5)

of the 25-pin connector on the PK-900's rear panel.

2.6.7 Other Computers with Non-Standard Serial Ports

Computers with non-standard serial ports must meet the following

conditions:

o The signal levels must be compatible with RS-232-C. The PK-900

requires the voltage levels from the computer be greater than +3

volts in the "asserted" state and 0 volts or less in the "non-

asserted" state.

o The signal polarity must conform to the RS-232-C standard. The

0 or negative-voltage state must correspond to logical "1" and

the positive-voltage state to logical "0."

o The computer must be able to correctly receive a signal that

meets asynchronous RS-232-C specifications. The PK-900

supplies signals that meet this specification.

Make or buy a cable that provides the following connections:

o The computer's serial port signal ground or common pin must be

connected to pin 7 of the PK-900's 25-pin connector.

o The pin on which the computer SENDS data must be connected to

pin 2 of the PK-900's 25-pin serial connector.

o The pin on which the computer RECEIVES data must be connected to

pin 3 of the PK-900's 25-pin serial connector.

If your computer requires any other signals, you must arrange to

provide them. The PK-900 has the standard hardware handshake lines

available. As a default the PK-900 provides XON/XOFF software flow

control to the computer or terminal. The command XFLOW can be turned

OFF disabling software flow control and enabling hardware handshake if

your computer requires it. The documentation provided with your

computer or serial card should clarify any special requirements.

2.7 Terminal (Modem) Software for Other Computers

Any communications program that enables your computer to emulate or

act as an ASCII terminal with a telephone modem should work with

your PK-900. If you have a familiar program you have used

successfully, use it to communicate with your PK-900.

1/93 2-11

Содержание PK-900









































































































































































































































































































































































































Результаты поиска

Содержание PK-900

Отзывы:

Похожие инструкции для PK-900

Бренды по названию

Популярные бренды

Timewave PK-900, Руководство по эксплуатации

Результаты поиска

Содержание PK-900

Отзывы:

Похожие инструкции для PK-900

Бренды по названию

Популярные бренды