Power Assisted Steering System: 6C-8
Air Bleeding Procedure
S3RH0A6306003
1) Jack up the front end of vehicle, and then apply
safety stands.
2) Fill P/S fluid reservoir with fluid up to specified level.
NOTE
Before starting engine, set transmission gear
shift lever in “Neutral” (shift selector lever to
“P” range for A/T model), and set parking
brake.
3) After running engine at idling speed for 3 to 5
seconds, stop it and add fluid to satisfy specification.
4) With engine stopped, turn steering wheel to the right
and left as far as it stops, repeat it a few times and fill
fluid to specified level.
5) With engine running at idling speed, repeat stop-to-
stop turn of steering wheel till all foams in P/S fluid
reservoir are gone.
NOTE
Make sure to bleed air completely. If air
remains in fluid, P/S pump may make
humming noise or steering wheel may feel
heavy.
6) Finally, check that fluid is filled to specified level.
P/S Pump Drive Belt On-Vehicle Inspection
S3RH0A6306004
1) Remove engine undercover of right side from vehicle
body.
2) Check belt for cracks, cuts, deformation, wear and
cleanliness.
If any defect is found, replace power steering belt.
Refer to “P/S Pump Drive Belt Removal and
Installation”.
3) Check belt tension by measuring how much it
deflects. Push the belt intermediate point between A/
C compressor pulley (2) or P/S pump pulley (1) and
crankshaft pulley (3). The push force (5) should be
about 100 N (10 kg, 22 lb). Adjust it if necessary
referring to “P/S Pump Drive Belt Tension
Adjustment”.
Deflection of P/S belt
“a”: 7 – 9 mm (0.28 – 0.35 in.) for new belt, 9 – 11
mm (0.35 – 0.43 in.) for used belt
“b”: 4 – 9 mm (0.16 – 0.35 in.) for new and used
belts
P/S Pump Drive Belt Tension Adjustment
S3RH0A6306005
1) Remove engine undercover of right side, and then
loosen tension pulley bolt (3).
2) To adjust P/S belt (5), loosen tension pulley nut (4),
and then turn tension pulley (1) counterclockwise or
clockwise by using special tool (A).
Special tool
(A): 09945–35410
3) Adjust belt tension to the following specification, and
then tighten tension pulley bolt and nut to specified
torque.
Tightening torque
Tension pulley bolt and nut (a): 25 N·m (2.5 kgf-
m, 18.0 lb-ft)
[A]: For vehicle with A/C system
[B]: For vehicle without A/C system
4. Tension pulley
a: Tight
6. P/S pump pulley
b: Loose
7. Crankshaft pulley
2. Tension pulley hole
4
3
2
“a”
“b”
[A]
[B]
3
1
4
1
5
5
I3RH0A630005-01
(A)
6
3, (a)
2
5
1
4, (a)
7
a
b
I2RH0B630004-01
Содержание Liana RH413
